Welcome to Cisco Support Community. We would love to have your feedback.
For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.
I am having AP 1131, with SSID - cisco vlan 31 and SSID -voice vlan 103, in my laptop I am able to see cisco ssid but not voice ssid, please light me what I am missing.
I have brand new 7921 IPPhone, in that I configur SSID as voice and cisco, but it says registration fails, in 7921 antenna I am not able to see any signal strength..
Please help us to solve this problem
No clients can associate to the voice ssid?
If so, if this is autonomous, then you need to add the ssid under the appropriate interfaces.
Then on the 7921 side, ensure you configure the 802.11 mode and security to match.
If you enter site survey mode, it should show the ap there if it responding to probe requests.
Please attach your AP config in order to get further assistance.
The below is the SH run config of my access point:
Current configuration : 2182 bytes
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
enable secret 5 $1$rCvL$/cBIHnneTcrz1OmcMYPe9.
no aaa new-model
dot11 ssid voice
dot11 arp-cache optional
power inline negotiation prestandard source
username Cisco password 7 14341B180F0B
no ip address
no ip route-cache
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
encapsulation dot1Q 103
bridge-group 103 subscriber-loop-control
bridge-group 103 block-unknown-source
no bridge-group 103 source-learning
no bridge-group 103 unicast-flooding
bridge-group 103 spanning-disabled
no dfs band block
ip helper-address 188.8.131.52
ip address dhcp client-id FastEthernet0
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
I have vlan 103, in switch vlan 103 is voice vlan, when I try laptop wirless, I am able see the voice network and related DHCP I am able to get. But in 7921 IPPhone is not get register.
In 7921 site survery it shows ch. AP name RSSI
as 01 [hostname] RSSI -27.
In profile1 [WLAN configuration] as follows:
SSID - voice
security mode - open
802.1 mode - auto-RSSI
Please light me what Iam missing to get regiaster IPPhonhe 7921.
The config looks good.
You are using open authentication without encryption, so ensure the security mode is set to Open.
Check the nework settings to see if the phone is getting a DHCP address.
Ensure the phone has at least 1.3(2) firmware loaded.
In 7921, The security mode is - open; 802.11 mode - auto-RSSI, call power save mode - u-apsd/PS-Poll.
DHCP Enabled - Yes.
But the 7921 is not get register with AP.
7921 Model Information as follows:
App LoadID CP7921G-MFG-C.2LOADS
Please light me what I am missing in IPPhone side.
You have a Call Manager right?
So is not getting an IP address...correct?
If not, ensure the AP switchport is set for trunnking mode and that VLAN is allowed on the uplinks.
Otherwise you can do a simple test and put the voice ssid into VLAN 1 temporarily to try, where then the switch will tag the packets.
If using the Cisco Unified Wireless IP Phone 7921G World (-W) model, then you must enable 802.11d, for example if you are in US, then need:
Interface dot11radio X
world-mode dot11d country US both