Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Users might experience few discrepancies in Search results. We are working on this on our side. We apologize for the inconvenience it may have caused.
New Member

7921 phone prefers the G band over A- why?

We are using 7921 phones over our wireless network with A, B and G APs. The phone is set to Auto-A and the APs are broadcasting the SSID over A and G bands. We are seeing the phones pick the G band 90% of the time. We restricted the SSID to the A radios and the phones worked just fine, but this goes against the philosophy of use A and fail over to G. The phones are using WPA, CCKM (TKIP) and have firmware v.1.3.2 (the 1.3.3 firmware had issues authenticating against RADIUS, but 1.3.2 works). Any ideas?

6 REPLIES
Cisco Employee

Re: 7921 phone prefers the G band over A- why?

Auto-A gives precedence to 5 GHz, but if unavailable it can switch to 2.4 GHz if available. There is no mechanism to re-scan the preferred band (5 GHz) after failing over to the less preferred band (2.4 GHz) at this time.

We recommend not to have 2.4 GHz signal for the voice ssid in areas where you want to use 5 GHz.

This may require separate WLC or the use of AP groups.

This is also documented in the 7921G Deployment Guide on page 50.

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/6_0/english/deployment/guide/7921dply.pdf

New Member

Re: 7921 phone prefers the G band over A- why?

Thanks for the response; I think this is exactly the issue we are seeing.

New Member

Re: 7921 phone prefers the G band over A- why?

Did you ever figure out why the 1.3.3 firmware had issues with authenticating against RADIUS? I am experiencing the same issue, I have a 7921 running 1.0.4 and one running 1.3.3 with identical settings, but the 1.3.3 one has the auth failures.

The only problem is that 1.3.3 can't be downgraded back to anything prior to 1.3.3, so we're stuck with it...

New Member

Re: 7921 phone prefers the G band over A- why?

No, I did not find a reason why; I simply downgraded to the earlier firmware. I did this by going into CM and specifying which firmware to use and this pushed it down to the phone.

Device>Device Settings>Device Defaults and change name to the older firmware.

Cisco Employee

Re: 7921 phone prefers the G band over A- why?

There was a change in the 1.3(2) release in order to pass WPA/WPA2 enterprise certification, which was to change the auth type from 128 (network-eap) to 0 (open) where EAP is optional.

If you are using the Cisco WLAN Controller, it supports both types by default.

If you are using the Cisco autonomous access points, then need to ensure that you have both methods enabled to cover all firmware versions.

See the 1.3(2) release notes.

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7925g/firmware/1_3_2/english/release/notes/792x_132.html#wp223099

There is nothing in 1.3(3) that I can think of that would impact authentication.

As far as roaming back to 5 GHz even though the voice ssid is still present on 2.4 GHz after failing over to 2.4 GHz when configured for Auto-a, we are planning to make some enhancements in this area for the 1.3(4) release, where it will scan both bands when in an auto mode and ensure it is on the preferred band when available.

New Member

Re: 7921 phone prefers the G band over A- why?

Thanks Michael, our issue is now resolved.

892
Views
5
Helpful
6
Replies
CreatePlease to create content