Our Customer is facing issue on their corporate SSID , We have capture debug and found below logs . Can anyone suggest what can be issue , currently WLC is on IOS 8.5.171.0 and access points connected AIR-CAP3702I-Z-K9.Debug logs apfMsConnTask_3: Apr...
Forum Posts
Can anybody tell me what exactly is the difference between the radio MAC address vs the ethernet and Wi-Fi mac addresses? What is the purpose of the radio MAC address? Apparently, wireless access points don't just have an ethernet and Wi-Fi MAC, but ...
We have a 9800-CL Wireless Controller running 17.12.2. We just got a new CW9164I-ROW AP and its registered by the operational interfaces are down due to a regulatory domain error. Is there a way to change the regulatory domain for the access point?...
Hello, I am using WLC 5508 8.3.133 and ipad as a client. I am trying to fix the roaming issue. Ap which gives me trouble is 3702iClient debug gives me this. Can someone explain it, please what is a reason for this error ? apfMsConnTask_5: Aug 24 14:...
Our WLCs currently have management access (HTTP/S, SSH, SNMP, etc.) restricted to certain IPs/subnets via an ACL in the router upstream. Is there a way to accomplish this on the controllers themselves, both for AireOS (version 8.10) and IOS (version ...
Hi, We have recently deployed Prime 3.10.2 and added a 9800-L (SW 17.6.4) along with 10 X 9130 APs.. On adding the APs to the site maps within Prime, there is no RF heat maps being emitted from them. Just wondering if any has come across this issue a...
Good afternoon,A new client is splitting off from a parent company this Fall. They current have AP1852E-B-K9 and WLC5200 and they want to migrate to 9800-WL. I will have an instance of the 9800-WL stood up before cutover, but once the WAN is moved fr...
What is the meaning of this Alert and what can I do to mitigate this. (for Unified Access Points)Message: '802.11a/n' interface of AP 'XXX' associated to controller 'XXXX)' is down. Reason: Radio reset due to (56) Radio channel set
Resolved! AP Alert
What is the meaning of this Alert as extracted from Cisco Prime Infrastructure.Message: Interference threshold violation reported by '802.11b/g/n' interface of AP 'XXX', connected to Controller 'XXX'.
Hello, I have a C9105AXW-B access point configured for office extend. When the AP is joined to an AireOS WLC (8.10.185.0) in office extend it doesn't broadcast a local personal SSID. When I join the AP to an IOS WLC (17.9.5) in office extend mode I...
We have created flex profile and local switched wlan (there are several APs in the facility, all of them are tagged with one and only flexconnect wlan/ssid, they all go through locally switched vlan 100 (no other SSIDs on AP, meaning no other central...
Hi I got a pair of 5520 in SSO mode version 8.10.190. If you want to run OEAP then you need to enable Enable NAT Address on the management interface. The problem is that the "Enable NAT Address" is greyed out: the question is: is it possible to enab...
Hi,with some Catalyst C9164 APs we have the problem that the image is corrupt.https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-9800-series-wireless-controllers/220443-how-to-avoid-boot-loop-due-to-corrupted.htmlCan the C9164 APs even u-bo...
i've seen this item "Site Tags AP to WNCd distribution" in best practice of C9800 Design and Deploymentmy quiestion is how can i configure multiple WNCd and where is the location of settings in webui?
We have configured two Lightweight Access Points using a 3504 WLC on Packet Tracer. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Au...
