Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Clients are unable to access a New wireless Controller 5508

Clients are unable to access the public ssid, which is wide open(or any other ssids).

I'm using LAG and I can ping each interface on the controller.  Ap's show a total of 2 and 2 are up. 

interface name is public vlan identifier 107, ip add 10.1.255.252, interface dynamic

Software version 7.0.98.0

Model No.AIR-CT5508-K9
Burned-in MAC Address50:3D:E5:1A:2F:60
Maximum number of APs supported25
FIPS Prerequisite ModeDisable
 

UDI :

 
Product Identifier DescriptionAIR-CT5508-K9
Version Identifier DescriptionV01
Serial NumberFCW1508L0KT
Entity NameChassis
Entity DescriptionCisco Wireless Controller

Profile Name
Type
SSID
Status
  Enabled
Security Policies
(Modifications done under security tab will appear after applying the changes.)
Radio Policy
Interface
Broadcast SSID
Enabled

Layer 2 security none

Below is the errors that are in the controller's log.

spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00

*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)

*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address

*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400  Join request does not contain BOARD_DATA payload

*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00

*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400  Join request does not contain BOARD_DATA payload
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP

I have attached show run-config and show running-config

3 REPLIES
Hall of Fame Super Silver

Clients are unable to access a New wireless Controller 5508

Are you sure your AP's are up and not bouncing?  Can you post your show run-config so we can see exactly how you have it setup.

-Scott
*** Please rate helpful posts ***

Clients are unable to access a New wireless Controller 5508

I attached the config to the first posting.  Thanks.

Clients are unable to access a New wireless Controller 5508

For the public WLAN, what is 10.1.1.1?  Is it a real DHCP server, is it a FW?  If it's a FW, then you'll need to disable dhcp proxy:

CLI config dhcp proxy disable

GUI Controller > Advanced > DHCp, and uncheck the box for proxy.

As for all of your other SSID, they are all pointd at the management interface.  Double check the WLAN config, and point them to the interface you want the user to get an IP address in.

HTH,

Steve

----------------------------------------------------------------------------------------------------------

Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
1761
Views
0
Helpful
3
Replies
CreatePlease login to create content