Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Web interface not work

Good morning, i've purchased an AP LAP 1131AG, i need to access in web interface but this not work.

i've configured  static ip means console port, i ping that ip , but when i try to access in web interface this not work.

this is my startup:

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...###########################

################################################################################

##############################################################

File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entr

y point: 0x3000

executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEA

SE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 17-Jul-06 11:38 by alnguyen

Image text-base: 0x00003000, data-base: 0x0035E440

Initializing flashfs...

flashfs[1]: 4 files, 2 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15998976

flashfs[1]: Bytes used: 1870848

flashfs[1]: Bytes available: 14128128

flashfs[1]: flashfs fsck took 4 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision B0) with 24566K/81

92K bytes of memory.

Processor board ID FCZ1407Q1SD

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from power-on

LWAPP image version 3.0.51.0

1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 88:43:E1:AA:1A:E4

Part Number                          : 73-8962-14

PCA Assembly Number                  : 800-24818-13

PCA Revision Number                  : A0

PCB Serial Number                    : FOC140453YY

Top Assembly Part Number             : 800-29144-03

Top Assembly Serial Number           : FCZ1407Q1SD

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1131AG-E-K9

Press RETURN to get started!

*Mar  1 00:00:06.307: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power s

ource

*Mar  1 00:00:06.313: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEA

SE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 17-Jul-06 11:38 by alnguyen

*Mar  1 00:00:07.267: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to

up

*Mar  1 00:00:08.267: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0, changed state to up

4 REPLIES
Gold

Re: Web interface not work

That AP is running a lightweigh image and doesn't have a web interface.  Are you planning on using this AP with a controller or as an autonomous AP?  If you want to use it as an autonomous AP you need to convert it:

http://www.cisco.com/en/US/docs/wireless/controller/6.0/configuration/guide/c60lwap.html#wp1105215

New Member

Re: Web interface not work

I need autonomous AP, for convert Ap i need the access point image file.

I can't download it from download area

Gold

Re: Web interface not work

You can use any of the autonomous IOS AP images to convert the AP.

New Member

Re: Web interface not work

where can i find autonomous IOS AP images ?

1510
Views
10
Helpful
4
Replies