Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

Autonomous IOS Support for 3500, 3600 and 1550 Series Access Points

 

 

Introduction

 

 

In the 15.2(2)JA release, Cisco supports running autonomous IOS (aIOS) only in "site survey" mode on the 3500, 3600 and 1550 Series Access Points.

 

Full feature support for 3500, 3600 and 1550 Series APs is only when running in lightweight mode (Cisco Unified Wireless Network.)

 

 

         3600.jpg

 

 

The following 15.2(2)JA aIOS images can be used in "site survey" mode on these APs:

  • ap3g1-k9w7-tar.152-2.JA.tar - this image can be used on a 1260 series AP with full feature support, or on a 3500 series AP in "site survey" mode
  • ap3g2-k9w7-tar.152-2.JA.tar - this image can be used on a 2600 series AP with full feature support, or on a 3600 series AP in "site survey" mode
  • c1520-k9w7-tar.152-2.JA.tar - this image supports only the 1550 series AP, and only in "site survey" mode.

 

 

"Site survey" mode is a subset of aIOS functions, and is defined in the 15.2(2)JA Release Notes.  There is no specific new feature to configure "site survey" mode; simply configure the desired functions on the access using ordinary IOS commands..

 

For more information on AP IOS, see the article Understanding Access Point IOS Images.

Comments

Thanks Aaron

New Member

Are we going back to WLC surveys then? I thought the days of AP1000 and WLC2006 were behind me

Good point Rob, nothing worse than trying to find power for a WLC when on a survey.!

Cisco advance team actuallys uses the 3500 with either the 1142 or the 1260 code. So no need for a WLC.

Yeh ive used the 1260 code for a while, but i was thinking of the 3600's :-)

New Member

Good point for the 3500, it was the 3600 that I was interested in.  Not even sure what an ap3g2 image is...

New Member

Hi,

does anybody know if there will an autonomous IOS for the 3600 in the future?

I need an n-AP that can be configured as WGB an has the "EN 50155" certification. There are the 1260s or the 3500s which can be configured as WGB but they are not "EN 50155" certified and the 3600s have the certification but no autonomous IOS...

New Member

Hello guys,

just wondering if you guys know about this, we were asked to do a survey using the 3600 , and like it said before it would be a pain to use a WLC for this,

Silver

The next release of autonomous IOS ("Nitrogen"), which should be out within a week or two, will support running a 3500 or 3600 (or 1550) AP in autonomous "site survey" mode.

New Member

That would be awesome, is really hard to make surveys using a WLC, speacilly on crowded environments like schools & hospitals

New Member

It is still available!!!

Site-Survey Only Mode for 3600, 3500, and 1550 Access Points

You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and  3500 Series access points and on 1550 series outdoor access points to  perform site surveys. This release runs on these access points with  limited functionality. You can manually adjust these settings on the  site-survey access points:

Channel on each radio

Transmit power on each radio

Enable and disable the radios

Manually set basic and supported transmit rates

Enable advertised cell power in beacons to client to enable DTPC for doing active surveys

Enable and disable SSID broadcast in beacons

Enable open authentication

New Member

I see this in the release notes but nothing is stated in the configuration guide on how to use it. How do you enable the site survey mode?

New Member

Hi,

there is no special Survey Mode. You can use the AP with this Software Version like a traditional autonomous AP! Everything is working you need for a Site Survey. You can configure it on the console or on the gui.

Last week i do a site survey with this IOS and a 3500 AP. It works fine!

New Member

Is the only way you can get this IOS on a 3600 to use a WLC?   I see no commands to do a copy or archive command to get it there via the CLI.

Hall of Fame Super Silver

You can issue a debug capwap console CLI

That will allow you to do the archive command or you can use the other methods shown in this document:

https://supportforums.cisco.com/docs/DOC-18268

Hall of Fame Super Silver
New Member

Outstanding, thank you!

Now if I can just suppress the capwap discovery process long enough to allow the tftp transfer to complete

Hall of Fame Super Silver

debug capwap cli no-reload

New Member

Scott, you rock!

Thanks so much for your help!

Kevin

Hall of Fame Super Silver

Glad I could help:)