Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

FUS image update on WLC

FUS image have to be updated from WLC Console only but it could change in future version. Require user to respond for below events.

Bundles included in this upgrade:

    - Bootloader

    - Field Recovery image

    - Offline Diagnostic image

    - FPGA image

    - Environment Controller (MCU) Image

    - USB Console image

(Cisco Controller) >show boot

Primary Boot Image............................... 7.2.103.0 (default)

Backup Boot Image................................ 7.2.103.0 (active)

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.2.103.0

Bootloader Version............................... 1.0.1

Field Recovery Image Version..................... 6.0.182.0

Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27

Build Type....................................... DATA + WPS

System Name...................................... Orange5508

System Location.................................. Orange High School MDF

System Contact................................... Bailey Communications

System ObjectID.................................. 1.3.6.1.4.1.9.1.1069

IP Address....................................... 10.93.2.2

Last Reset....................................... Software reset

System Up Time................................... 0 days 0 hrs 8 mins 4 secs

System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)

Configured Country............................... US  - United States

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +40 C

--More-- or (q)uit

External Temperature............................. +21 C

Fan Status....................................... OK

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 1

Number of Active Clients......................... 0

Burned-in MAC Address............................ 64:9E:F3:BF:61:80

Power Supply 1................................... Present, OK

Power Supply 2................................... Present, OK

Maximum number of APs supported.................. 100

(Cisco Controller) >

Updating license storage ...  Done.

Restarting system.

þ

WLCNG Boot Loader Version 1.0.1 (Built on Apr 11 2009 at 13:32:33 by cisco)

Board Revision 1.3 (SN: FCW00000000, Type: AIR-CT5508-K9) (G)

Verifying boot loader integrity... OK.

OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)

FPGA Revision 1.3

Env FW Revision 1.6

USB Console Revision 1.27

DRAM:  1024 MB

Flash: 32 MB

Clearing DRAM........ done

Network: octeth0', octeth1

  ' - Active interface

  E - Environment MAC address override

CF Bus 0 (IDE): OK

IDE device 0:

- Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MNZ111291155953

- Type: Hard Disk

- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press <ESC> now to access the Boot Menu...

Loading primary image (7.2.103.0)

100%

6183766 bytes read

Launching...

init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary

starting pid 821, tty '': '/etc/init.d/rcS'

Field Upgrade Software

Bundles included in this upgrade:

    - Bootloader

    - Field Recovery image

    - Offline Diagnostic image

    - FPGA image

    - Environment Controller (MCU) Image

    - USB Console image

      ******************************************************************

      * Please make sure POWER SUPPLY is always ON during this period. *

      * Lost POWER will completely kill this unit and not recoverable. *

      * There may be multiple reboot. Please let the program run.      *

      ******************************************************************

      Start soon ...

====================

Checking for Bootloader upgrade

Bootloader upgrade ...

Upgrade Bootloader from 1.0.1 to 1.0.16

        ******************************************************************

        * Upgrade takes about 41 seconds to complete.                    *

        * Please make sure POWER SUPPLY is always ON during this period. *

        * Lost POWER will completely kill this unit and not recoverable. *

        ******************************************************************

        Are you sure you want to proceed (y/N) ? y

Erasing Flash (estimated 6 seconds) ...

Writing to Flash (estimated 41 seconds) ...

Checking Boot loader integrity (estimated 2 seconds) ... OK.

====================

Checking for FPGA upgrade

FPGA upgrade ...

        Upgrading FPGA from rev 1.3 to rev 1.7

        ******************************************************************

        * Upgrade takes about 75 seconds to complete.                    *

        * Please make sure POWER SUPPLY is always ON during this period. *

        * Lost POWER will completely kill this unit and not recoverable. *

        ******************************************************************

        Are you sure you want to proceed (y/N) ? y

bulk erase...

write 215059 bytes............................................................................

FPGA upgrade complete succesfully

System is now rebooting...þ

WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)

Board Revision 1.3 (SN: FCW1552L0MJ, Type: AIR-CT5508-K9) (P)

Verifying boot loader integrity... OK.

OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)

FPGA Revision 1.7

Env FW Revision 1.6

USB Console Revision 1.27

CPU Cores:  10

DRAM:  1024 MB

Flash: 32 MB

Clearing DRAM........ done

Network: octeth0', octeth1

  ' - Active interface

  E - Environment MAC address override

CF Bus 0 (IDE): OK

IDE device 0:

- Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MNZ111291155953

- Type: Hard Disk

- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press <ESC> now to access the Boot Menu...

Loading primary image (7.2.103.0)

100%

6183766 bytes read

Launching...

init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary

starting pid 821, tty '': '/etc/init.d/rcS'

Field Upgrade Software

Bundles included in this upgrade:

    - Bootloader

    - Field Recovery image

    - Offline Diagnostic image

    - FPGA image

    - Environment Controller (MCU) Image

    - USB Console image

      ******************************************************************

      * Please make sure POWER SUPPLY is always ON during this period. *

      * Lost POWER will completely kill this unit and not recoverable. *

      * There may be multiple reboot. Please let the program run.      *

      ******************************************************************

      Start soon ...

====================

Checking for MCU upgrade

Environment controller upgrade ...

        Upgrading Env from rev 1.6 to rev 1.8

        ******************************************************************

        * Upgrade takes about 4 seconds to complete.                    *

        * Please make sure POWER SUPPLY is always ON during this period. *

        * Lost POWER will completely kill this unit and not recoverable. *

        ******************************************************************

        Are you sure you want to proceed (y/N) ? y

........................................................

Env upgrade complete succesfully

System  will reset in 10 seconds ...

Waiting for reboot ...

þ

WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)

Board Revision 1.3 (SN: FCW1552L0MJ, Type: AIR-CT5508-K9) (P)

Verifying boot loader integrity... OK.

OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)

FPGA Revision 1.7

Env FW Revision 1.8

USB Console Revision 1.27

CPU Cores:  10

DRAM:  1024 MB

Flash: 32 MB

Clearing DRAM........ done

Network: octeth0', octeth1

  ' - Active interface

  E - Environment MAC address override

CF Bus 0 (IDE): OK

IDE device 0:

- Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MNZ111291155953

- Type: Hard Disk

- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press <ESC> now to access the Boot Menu...

Loading primary image (7.2.103.0)

100%

6183766 bytes read

Launching...

init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary

starting pid 821, tty '': '/etc/init.d/rcS'

Field Upgrade Software

Bundles included in this upgrade:

    - Bootloader

    - Field Recovery image

    - Offline Diagnostic image

    - FPGA image

    - Environment Controller (MCU) Image

    - USB Console image

      ******************************************************************

      * Please make sure POWER SUPPLY is always ON during this period. *

      * Lost POWER will completely kill this unit and not recoverable. *

      * There may be multiple reboot. Please let the program run.      *

      ******************************************************************

      Start soon ...

====================

Checking for usbcon upgrade

USB upgrade ...

        Upgrading USB from rev 1.27 to rev 2.2

        ******************************************************************

        * Upgrade takes about 11 seconds to complete.                    *

        * Please make sure POWER SUPPLY is always ON during this period. *

        * Lost POWER will completely kill this unit and not recoverable. *

        ******************************************************************

        Are you sure you want to proceed (y/N) ? y

Starting USB Console Programming

####################################

Programming Complete!

====================

Checking for Offline Diagnostic image upgrade

Offline Diagnostic upgrade ...

        Upgrade OFD from version WLCNG OFD 0.8.1 to WLCNG OFD 0.9.28

        Are you sure you want to proceed (y/N) ? y

        ******************************************************************

        * Please make sure POWER SUPPLY is always ON during this period. *

        ******************************************************************

Erasing Flash (estimated 24 seconds) ...

Writing to flash (estimated 111 seconds) ...

====================

Checking for Field recovery image upgrade

Field Recovery Image upgrade ...

        Upgrade Field Recovery Image from version 6.0.182.0 to 7.0.112.21

        Are you sure you want to proceed (y/N) ? y

        ******************************************************************

        * Please make sure POWER SUPPLY is always ON during this period. *

        ******************************************************************

Erasing Flash (estimated 49 seconds) ...

Writing to flash (estimated 716 seconds) ...

All upgrades done. System reboot ...

Restarting system.

WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)

Board Revision 1.3 (SN: FCW1552L0MJ, Type: AIR-CT5508-K9) (G)

Verifying boot loader integrity... OK.

OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)

FPGA Revision 1.7

Env FW Revision 1.8

USB Console Revision 2.2

CPU Cores:  10

DRAM:  1024 MB

Flash: 32 MB

Clearing DRAM........ done

Network: octeth0', octeth1

  ' - Active interface

  E - Environment MAC address override

CF Bus 0 (IDE): OK

IDE device 0:

- Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MNZ111291155953

- Type: Hard Disk

- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press <ESC> now to access the Boot Menu...

Loading primary image (7.2.103.0)

100%

30907681 bytes read

Launching...

init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary

starting pid 821, tty '': '/etc/init.d/rcS'

type = block

dump-device = 254:4

disrupt

level = header

compress = none

Set PLX switch MPS settings .............!!!!!!!

Detecting Hardware ...

set smp_affinity for irq 48

003f

DP from CGE5.0 ...

starting pid 1052, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar'

Cryptographic library self-test....passed!

XML config selected

Validating XML configuration

octeon_device_init: found 1 DPs

readCPUConfigData: cardid 0x6070001

Node ptr_simCfgData.serialPortTimeOut value = 4650 is out of range for min = 0 and max = 2580

Validation for node ptr_simCfgData.serialPortTimeOut failed

Cisco is a trademark of Cisco Systems, Inc.

Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 7.2.103.0

Firmware Version FPGA 1.7, Env 1.8, USB console 2.2

Initializing OS Services: ok

Initializing Serial Services: ok

Initializing Network Services: ok

Initializing Licensing Services: ok

License daemon start initialization.....

License daemon running.....

Starting ARP Services: ok

Starting Trap Manager: ok

Starting Network Interface Management Services: ok

Starting System Services: ok

Starting FIPS Features: ok : Not enabled

Starting Fastpath Hardware Acceleration: ok

Starting Fastpath Console redirect : ok

Starting Fastpath DP Heartbeat : ok

Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok

Fastpath CPU0.00: Initializing last packet received queue. Num of cores(10)

Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040

Fastpath CPU0.00: Core 0 Initialization and FIPS self-test: ok

Fastpath CPU0.00: Initializing Timer...

Fastpath CPU0.00: Initializing Timer...done.

Fastpath CPU0.01: Core 1 Initialization and FIPS self-test: ok

Fastpath CPU0.01: Received instruction to get link status

Fastpath CPU0.02: Core 2 Initialization and FIPS self-test: ok

Fastpath CPU0.03: Core 3 Initialization and FIPS self-test: ok

Fastpath CPU0.04: Core 4 Initialization and FIPS self-test: ok

Fastpath CPU0.05: Core 5 Initialization and FIPS self-test: ok

Fastpath CPU0.06: Core 6 Initialization and FIPS self-test: ok

Fastpath CPU0.07: Core 7 Initialization and FIPS self-test: ok

Fastpath CPU0.08: Core 8 Initialization and FIPS self-test: ok

Fastpath CPU0.09: Core 9 Initialization and FIPS self-test: ok

Starting Switching Services: ok

Starting QoS Services: ok

Starting Policy Manager: ok

Starting Data Transport Link Layer: ok

Starting Access Control List Services: ok

Starting System Interfaces: ok

Starting Client Troubleshooting Service: ok

Starting Management Frame Protection: ok

Starting Certificate Database: ok

Starting VPN Services: ok

Starting Licensing Services: ok

Starting LWAPP: ok

Starting CAPWAP: ok

Starting LOCP: ok

Starting Security Services: ok

Starting Policy Manager: ok

Starting Authentication Engine: ok

Starting Mobility Management: ok

Starting Virtual AP Services: ok

Starting AireWave Director: ok

Starting Network Time Services: ok

Starting Cisco Discovery Protocol: ok

Starting Broadcast Services: ok

Starting Logging Services: ok

Starting DHCP Server: ok

Starting IDS Signature Manager: ok

Starting RFID Tag Tracking: ok

Starting Power Supply and Fan Status Monitoring Service: ok

Starting Mesh Services:  ok

Starting TSM: ok

Starting CIDS Services: ok

Starting Ethernet-over-IP: ok

Starting DTLS server:  enabled in CAPWAP

Starting Mobile Concierge: ok

Starting CleanAir: ok

Starting WIPS: ok

Starting SSHPM LSC PROV LIST: ok

Starting RRC Services: ok

Starting RF Profiles: ok

Starting SXP Services: ok

Starting FMC HS: ok

Starting IPv6 Services: ok

Starting Management Services:

   Web Server:    CLI: ok

   Secure Web: ok

   License Agent: ok

(Cisco Controller)

Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)

User:  administrator

Password:********

(Cisco Controller) >show boot

Primary Boot Image............................... 7.2.103.0 (default) (active)

Backup Boot Image................................ 6.0.199.4

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.2.103.0

Bootloader Version............................... 1.0.16

Field Recovery Image Version..................... 7.0.112.21

Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2

Build Type....................................... DATA + WPS

System Name...................................... Orange5508

System Location.................................. Orange High School MDF

System Contact................................... Bailey Communications

System ObjectID.................................. 1.3.6.1.4.1.9.1.1069

IP Address....................................... 10.93.2.2

Last Reset....................................... Software reset

System Up Time................................... 0 days 0 hrs 1 mins 51 secs

System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)

Configured Country............................... US  - United States

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +38 C

--More-- or (q)uit

External Temperature............................. +21 C

Fan Status....................................... OK

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 1

Number of Active Clients......................... 0

Burned-in MAC Address............................ 64:9E:F3:BF:61:80

Power Supply 1................................... Present, OK

Power Supply 2................................... Present, OK

Maximum number of APs supported.................. 100

(Cisco Controller) >

*** IDLE TIMEOUT ***

(Cisco Controller)

Version history
Revision #:
1 of 1
Last update:
‎04-08-2012 11:07 AM
Updated by:
 
Labels (1)
Comments
Cisco Employee

Thanks for the information Van. The FUS document is very confusing.