Wireless

Hi, everyoneI have some puzzle for WLC's L2 LWAPP and L3 LWAPP1, Is it right for the following depolyment: 4404 have 4 GE distribute port, For L2 LWAPP, on each corresponding port on switch, the first should be trunk, the last 3 should be access st...

Hi, I've a network with a lot of 7921 ( more than 50 ) connected to a lwapp wifi network:- 7921 with 1.1.1 firmware- wlc 4402 with 4.2.112- ccm 6.0.1- enabled WMM and CAC on controller - Qos platinum ( for voice )Does anyone had similar configuratio....

I'm receiving the following message...Error Message %LWAPP-3-DISC_INTF_ERR2: Ignoring discovery request received on a wrong VLAN (205) on interface (990) in L3 LWAPP mode.The WiSM module in the 6500 is configured with its AP Manager and Management...

Hello,I am trying to install a Linksys WCG200 wireless router in my SOHO office with five employees. How do I configure it so that people in the neighboring office don't get access to any data moving on this network? Thanks in advance for any help th...

We have a 4402 controller managing 27 ap's. When we connect new laptops to the WLAN, we cannot join the domain but can get on the internet, so it doesn't look like a DNS issue. If we plug the laptop into a network drop, it can join the domain fine.Al...

Following scenario:I have a root bridge with wireless client and a non root bridge with wireless client. This works fine, now I need to have a WGB. This works only when the WGB is associated with the "root bridge with wireless client". The WGB do not...

heyi have a WLC4402 with close to 20 laps.the Laps are broadcasting two wlans one for guest and one for corporate.recently i did an upgrade on the wlc from image 3.2.119.x to 4.0.219.0.now the problem is that the guest wlan cannot get ip address form...

Ive been trying to get my new AP521 to work for some time now, but I finally got the idea that it might only work with other Cisco gear.According to the extremely limited documentation there is from Cisco it seems that you can only assign it an IP ad...

I am going to be implementing a solution for 2 sites seperated by a WAN, each site will have 1 controller, and there will be one additional controller at the main site which will serve as the backup controller for both sites. I am a little unsure on...

i have converted Autonomous 1242AG series Ap into lightweight mode.i am using 2106 WLC with software version 4.1.185.the Ap doesn't associate the controller .its produce the following error:Mar 1 00:00:38.071: LWAPP_CLIENT_ERROR: lwapp_name_lookup -...

I've just upgraded an autonomous 1131AG AP to use the LWAPP image and it refuses to connect to my 4402 WLC. Debugging LWAP events shows an invalid country code shown in the output below:Tue Mar 25 09:59:03 2008: 00:1b:2b:68:85:e0 Received LWAPP CONFI...

I'm experiencing problems with WCS. After the installation i want to start the WCS program. An error occurs all the time: Starting WCSCannot run with the current schema. Exiting.Apache server is already stopped.Failed to start WCS server.Is this a k...

Is it possible to limit which SSID's particular AP's broadcast? I've tried using AP Groups, but that only segments the VLAN broadcast domain. The AP still broadcasts all SSID's. I have 2 APs in a jury waiting room - I only want to broadcast their ...

Our Vista clients are having connection issues that doesn't seem to effect XP. I have several 1250's running LWAPP connected to a 2106 WLC (all behind a 3106 NAC Appliance). I have 2 laptops at my desk. One is running XP and another is running Vista....