Looking for a good program to convert AUTOCAD .dwf files into .jpg for importing into WCS. Having issues with Visio. Thanks
Looking for a good program to convert AUTOCAD .dwf files into .jpg for importing into WCS. Having issues with Visio. Thanks
I configured my 1130AG as a DHCP server. The WAP is on a vlan. I am connected to a 2801 through an HWIC-4ESW-POE. My clients connect but I cannot access the Internet. As part of the DHCP configuration I identified my default router(gateway) using the...
I have observed newly-installed LAP-1131AG access points that have been "primed" to a particular controller. When we boot them up with the same WLC controller to which they are primed, they eventually turn light green (which according to the documen...
I have a 1231G autonomous unit and a 4404 wireless controller, both reside on the same subnet, the controller is in layer 2 mode and has the bare necessities configured at present. I converted the 1231G to LWAPP, which was successful. But the LWAP ...
Greetings,If I have two different WLANs, both configured for WPA-PSK, are the pre-shared keys different per WLAN?I ask because when I change the PSK on one WLAN, it seems that this may be affecting the other WLAN.I'm not on-site to test this out, unf...
Hi,I would like to setup 2 branch with hybrid reap access point.I did standardize the vlan assignment for the hybrid reap access point ( let say vlan 2).Since all the configuration done through WLC. Is there a way to configure using the same vlan id ...
Hello everybody,I am a bit confused about cisco 1000 series access point connection. On wireless lan controller and lightweight access point basic configuration example document id 69719 (http://www.cisco.com/en/US/products/ps6366/products_configurat...
We have a (brand new) WiSM blade installed in a 6509. The configuration looks ok, but when we try to register (join?) an AP with the controler the process fails. The controler shows the AP in the status display but the AP reboots, claiming that no ...
As the title suggests, I can only get one wireless client to connect successfully to the AP when I am using WPA-PSK. The Client Computers (winxp sp2) attempt to connect, I can see the client attempts to connect to the AP, but they never get an IP add...
I'm trying to deploy an AP-1220B that's had issues for a long time; I seem to have isolated the cause to CRC errors on the Ethernet interface.I've attached the config of the WAP; can anyone point out any anomalies that need to be corrected? I've done...
Hi,I'm setting up my ACS server using MAC address to authenticate. I've over 1500 MAC addresses thus is there any way to mass import the MAC addresses into the ACS?With regards
could please anyone suggest me how to how to configure ip adresses for wlanwith 5 users.
I have 7920s using open authentication with WEP128 cipher. I have two 1300 root AP's (with client support) and three non-root AP's (also client support) in the same lab area. The root AP's and non-Root AP's associate and link to each other no problem...
I'm using two wgb350's in a bridge spanning about 1 mile. The antenna check shows 98% link and netstumbler on one end looking at the root-bridge shows 32-36db SNR. The link runs fine for about 98% of the time. However for about 2hrs in the afternoo...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-12-2024 05:27 AM | ||
04-10-2024 01:01 PM | ||
04-05-2024 06:44 PM | ||
04-04-2024 03:18 AM | ||
03-27-2024 07:38 AM |
User | Count |
---|---|
13 | |
4 | |
2 | |
2 | |
2 |