Wireless

I have a Cisco AP352E2R that appears dead; When powered on, the Ethernet light stays on red, Association status stays on Green, and the Radio Activity stays on Orange. The first time I plug it in, my USB Serial adapter shows no activity. If I unplug ...

Hi guys...In our office we have a Cisco Linksys Access Point. At a time a max of 5 will be connected. We do the MAC authentication. Every day when i start my work i am finding a great trouble for getting connected to network. It takes atleast 15-20 m...

I have two WLC4404-100 controllers where I just installed the secondary unit. I have edited certain APs to make the primary controller be this new unit and the current controller to be the secondary. These APs do not move unless I reset them. These A...

I configured wlse (2.12) to send e-mail notifications to my address, but i don't received anyone and then i run "show maillog" and this is the result :Dec 28 15:26:28 wlse sendmail[6444]: jBSFQSm06441: to=javalxxx@xxxx.es, ctladdr=casuser (200/200), ...

I have two 1131AG’s (12.3(7)JA1) in my environment that I am currently using WPA-PSK for encryption. I am using the same 63 character PSK on both AP’s. I am running multiple VLAN’s through both access points.My scenario:I take my laptop, select which...

Hello, I can't view 2006 wireless clients reports in the Cisco Works Wireless LAN Solution Engine. I can only select years from 2002 to 2005.Is it a bug? or am I the only one with this problem?I have installed the last firmware 2.12Thanks

HelloHow can i configure the wlan on cisco 1812w?I have a VLAN with connection to WAN.This VLAN have an DHCP.If i connect with RJ45 all its ok (DHCP and connection to outside). Ping to the gateway it´s okBut if i try to connect from WLAN the DHCP its...

Hi All,This is a little simple for those who have faced the problem but a little lengthy for those who have not come accross the same. Please grab a coffee before we begin.Scenario: Am trying to have EAP authentication for my wireless users to be aut...

We have 1300s in a point to multipoint with 2 in root mode. I found that the root 1300s can pick a channel, but the setting always returns to "least congested" for the 1300s in non-root mode. We want the bridge to favor one, but use the other as a ...

Hi All,I have 1100 series access point, where as it my clients are 802.11B. The clients are not detecting this network.so what are the changes i need APsPlease help me out on this issueThanks,Srikanth

Hi,I've an existing WLAN network of about 15 APs running WPA. The number of APs is expected to increase to aboute 30-50. As I would like to have better RF & AP management and also rouge AP detection & suppression, I'm looking at getting either gettin...

hi all,I could not get the WLC 2006 to communicate with the AP1010. My configuration is straight forward. WLC2006----CE500----AP1010DHCP Server (192.0.2.222) also connected to the CE500. The DHCP server can ping the WLC2006 and likewise.configuration...

I selected 3 AP1231s running 12.3(2)JA to do a AP Radio Scan;Job shows ended one hour ago, but the radio data is still old. Site Survey Wizard - AP Radio Scan 3154 12:43:56 12/29/2005 No Yes - 12:43:56 12/29/2005 12:54:16 12/29/2005 jaarons The Job ...

I am thinking to setup a wireless network (Cisco Airespace controller 4100) using EAP-PEAP for authentication. We have a Microsoft 2003 server running IAS. My understanding is that a server side certificate is needed at the MS IAS server. I don't ...

Hi everybody.¿Where can I find an estimation of the coverage ranges that can be obtained with the AP 1200 and omnidirectional antennas of different gain?Thanks