Wireless

Resolved! Controller to Manage Branches

Hi, Is it possible to deploy one controller for a company that has branches? Deploy it at the head Office provision the AP's then place those AP's at branches but manage them using one controller at the head office? If yes what should be configured?

Resolved! Ap With static ip Address reboot and the AP change de IP Address

Hello All! We have a lot of AP with STATIC IP but when any AP rebooting for power of or another matter, the IP Address of the AP change and we have to change it. Anyone know what happen? Thanks. Best regards.

Autonomous firmware for Cisco 3602i

Hi guys, I need some help downloading the latest autonomous firmware for my 3602i . I am unable to download software from CISCO right now and i really need that firmware. Can someone help? Thanks, Cristian

Resolved! AP not Found in a Controller

Hi, I am a first time installer I have installed my wireless controller and it is visible on the network but the APs are not visible on the controller what should I do. When i Console into the AP it gives me Some error msg Please see the attache...

IP scopes CBR-8

Where are the subscriber scopes located on a Cisco CBR8?

Resolved! New ETSI 301893 regulation

Hi all The latest WLC releases (8.3.143.0 and 8.5.131.0) state that they follow the new ETSI 301 893 regulation. I have read now into this document (a little), download: http://www.etsi.org/deliver/etsi_en/301800_301899/301893/02.01.01_60/en_301893v0...

Resolved! ISE-- what is the difference between L-ISE-TACACS= and L-ISE-TACACS-ND=

Hi, I am looking for when we should below mwntioned ISE part numbers -ISE-TACACS= and L-ISE-TACACS-ND= BR Jasim

Static IP issue

Hello I have a problem with connecting one client with static ip to the wlan. DHCP require is disable, passive client is disable. Wlc cannot obtain client ip address: *Dot1x_NW_MsgTask_0: Jun 18 14:15:39.962: xx:xx:xx:xx:xx:xx 0.0.0.0 DHCP_REQD (...

Cisco Prime Infrastructure 3.2 Root Templates available to other users

I am looking for the possibility to make templates created by the root available to other users (without root authorization), so that uniform templates can be used.Is this possibility available at Cisco Prime! Version: Cisco Prime Infrastructure 3.2....

Resolved! AP support Workgroup bridge

Hi Could someone help me to inform me that which AP can configure with workgroup bridge because I have plan to connect five sites to the master site via wireless connection. many thanks

5Ghz Channels for Indoors and Outdoors for E domain and A domain Access Points?

Hello Experts, Are the channels 36 through 64 meant only for Indoors usage only and cannot be used in outdoors? Do we have any documentation that lists out the channels in 5GHz for Indoors only and those that can be used even in outdoors against...

Resolved! Azimuth and Elevation planes on Antenna 2544

Hi experts, I was checking the AIR-ANT2544V4M-R for a warehouse and in the datasheet, there are these caracteristics that I don't really understand : Azimuth plane (3 dB beamwidth) : omnidirectional Elevation plane (3 dB beamwidth) 2.4 GHz band :...

Resolved! WLC 2504

hola quiero configurar de forma automatica unos 15 equipos AP-CAP3501 -3502 pero havia una manera que cada ves que los conecte si encuntra el WLC se auto configuren solos sin necesidad de configurar uno por uno puedes ayudarme con eso por favor graci...

Optimized Roaming vs Client Roaming

Cisco 7510 WLC - Having an issue at one site where device has to get a poor signal before hopping to the next access points. This is on the 2.4GHz band and all speeds below 11Mbps have been disabled. My question is for someone to explain the differ...