cancelar
Mostrando los resultados de 
Buscar en lugar de 
Quiere decir: 
Avisos
¡Bienvenido a la nueva Comunidad de Soporte de Cisco! Nos encantaría conocer su opinión
New Member

Issue in joining 2602i to 3850 wlc

Trying to join 2602i to 3850 wlc but after join the access point keeps rebooting

AP Console log:

APc067.afa7.1ee4#
*Nov 29 23:32:55.027: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Nov 29 23:32:55.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.129.0.254 peer_port: 5246
*Nov 29 23:32:55.223: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.129.0.254 peer_port: 5246
*Nov 29 23:32:55.223: %CAPWAP-5-SENDJOIN: sending Join Request to 10.129.0.254
., 1)29 23:33:13.415: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNKNOWN_MESSAGE_TYPE (5)
*Nov 29 23:33:13.415: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Nov 29 23:33:19.299: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Nov 29 23:33:19.319: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Nov 29 23:33:19.323: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Nov 29 23:33:19.327: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 29 23:33:19.347: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 29 23:33:20.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Nov 29 23:33:20.351: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Nov 29 23:33:20.359: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Nov 29 23:33:21.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Nov 29 23:33:21.351: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Nov 29 23:33:21.379: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 29 23:33:21.387: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Nov 29 23:33:21.395: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 29 23:33:22.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Nov 29 23:33:22.387: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Nov 29 23:33:22.415: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 29 23:33:23.415: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Not in Bound state.
*Nov 29 23:34:14.847: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Nov 29 23:34:19.847: %CAPWAP-3-ERRORLOG: Invalid event 40 & state 2 combination.
*Nov 29 23:34:19.967: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.129.0.212, mask 255.255.255.128, hostname APc067.afa7.1ee4

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Nov 29 23:34:25.847: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Nov 29 23:34:34.847: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Nov 29 23:35:04.847: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Nov 29 23:35:04.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.129.0.254 peer_port: 5246
*Nov 29 23:35:04.223: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.129.0.254 peer_port: 5246
*Nov 29 23:35:04.223: %CAPWAP-5-SENDJOIN: sending Join Request to 10.129.0.254
., 1)29 23:35:22.411: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNKNOWN_MESSAGE_TYPE (5)
*Nov 29 23:35:22.411: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Nov 29 23:35:27.479: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Nov 29 23:35:27.499: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Nov 29 23:35:27.499: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Nov 29 23:35:27.503: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 29 23:35:27.527: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 29 23:35:28.503: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Nov 29 23:35:28.531: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Nov 29 23:35:28.539: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Nov 29 23:35:29.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Nov 29 23:35:29.531: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Nov 29 23:35:29.559: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 29 23:35:29.567: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Nov 29 23:35:29.575: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 29 23:35:30.559: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Nov 29 23:35:30.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Nov 29 23:35:30.595: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 29 23:35:31.595: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

WLC Log:

Nov 29 23:40:46.469: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP c0:25:5c:68:7f:10

Nov 29 23:40:46.469: *%LWAPP-3-RD_ERR9: 1 wcm:  APs c0:25:5c:68:7f:10 country code changed from () to (GB )

Nov 29 23:40:46.470: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.

Nov 29 23:40:46.471: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP c0:25:5c:68:7f:10

Nov 29 23:40:46.471: *%LWAPP-3-RD_ERR9: 1 wcm:  APs c0:25:5c:68:7f:10 country code changed from () to (GB )

Nov 29 23:40:46.471: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:68:7f:10

54C1BR01A01254#

Nov 29 23:40:46.474: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:68:7f:10

Nov 29 23:40:46.474: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm:  Failed to create CAPWAP data tunnel with interface id: 0xd670c00000002a for AP: c025.5c68.7f10 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.

Nov 29 23:41:09.584: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination

Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination

Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP c0:25:5c:68:7f:10

Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR9: 1 wcm:  APs c0:25:5c:68:7f:10 country code changed from () to (GB )

Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP c0:25:5c:68:7f:10

Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR9: 1 wcm:  APs c0:25:5c:68:7f:10 country code changed from () to (GB )

Nov 29 23:42:55.496: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:68:7f:10

54C1BR01A01254(config)#

Nov 29 23:42:55.499: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.

Nov 29 23:42:55.499: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:68:7f:10

Nov 29 23:42:55.500: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm:  Failed to create CAPWAP data tunnel with interface id: 0xcb73c00000002b for AP: c025.5c68.7f10 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.

GB  - United Kingdom : 802.11a Indoor,Outdoor/ 802.11b / 802.11g

Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination
Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP c0:25:5c:68:7f:10
Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR9: 1 wcm:  APs c0:25:5c:68:7f:10 country code changed from () to (GB )
Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP c0:25:5c:68:7f:10
Nov 29 23:42:55.496: *%LWAPP-3-RD_ERR9: 1 wcm:  APs c0:25:5c:68:7f:10 country code changed from () to (GB )
Nov 29 23:42:55.496: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:68:7f:10

Nov 29 23:42:55.499: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.
Nov 29 23:42:55.499: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:68:7f:10
Nov 29 23:42:55.500: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm:  Failed to create CAPWAP data tunnel with interface id: 0xcb73c00000002b for AP: c025.5c68.7f10 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.

Sh Wirless Country Configured:

GB  - United Kingdom : 802.11a Indoor,Outdoor/ 802.11b / 802.11g

6 RESPUESTAS
Hall of Fame Super Gold

Re: Issue in joining 2602i to 3850 wlc

Nov 29 23:40:46.469: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP c0:25:5c:68:7f:10

Nov 29 23:40:46.469: *%LWAPP-3-RD_ERR9: 1 wcm:  APs c0:25:5c:68:7f:10 country code changed from () to (GB )

Post the output to the AP command "sh version".  I have a strange feeling your WLC is configured for GB but your AP has the wrong regulatory domain.

New Member

Issue in joining 2602i to 3850 wlc

Sh ver:

Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JN, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 01-Oct-13 19:18 by prod_rel_team

ROM: Bootstrap program is C3600 boot loader
BOOTLDR: C3600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)

APc067.afa7.1ee4 uptime is 6 hours, 57 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-k9w8-mx.152-4.JN/ap3g2-k9w8-xx.152-4.JN"
Last reload reason:

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-CAP2602I-E-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FCZ1743P1VC
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 10.1.100.0
1 Gigabit Ethernet interface
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C0:67:AF:A7:1E:E4
Part Number                          : 73-14588-02
PCA Assembly Number                  : 800-37899-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17353HXS
Top Assembly Part Number             : 800-38356-01
Top Assembly Serial Number           : FCZ1743P1VC
Top Revision Number                  : A0
Product/Model Number                 : AIR-SAP2602I-E-K9

Configuration register is 0xF

APc067.afa7.1ee4#

New Member

Issue in joining 2602i to 3850 wlc

Additional log from WLC:

Nov 30 06:47:33.336: *%LOG-3-Q_IND: 1 wcm:  Invalid AP event (CAPWAP Discovery R  equest) and state (CAPWAP Join Response) combination

Nov 30 06:47:33.336: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event () and state (CAPWAP Join Response) combination

Nov 30 06:50:23.296: *%LWAPP-3-RD_ERR4: 1 wcm:  Invalid regulatory domain 802.11bg:-A     802.11a:-A for AP c0:25:5c:68:7f:10

Nov 30 06:50:23.297: *%CAPWAP-3-POST_DECODE_ERR: 1 wcm:  Post decode processing failed for Config status from AP c025.5c68.7f10

Nov 30 06:50:23.301: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.

Nov 30 06:50:23.301: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm:  Failed to create CAPWAP data tunnel with interface id: 0xeb5c00000000f1 for AP: c025.5c68.7f10 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.

Hall of Fame Super Gold

Issue in joining 2602i to 3850 wlc

And you are sure your WLC is configured ONLY for GB (-E) and nothing else?

New Member

Issue in joining 2602i to 3850 wlc

sh wireless country configured

Configured Country.............................: GB  - United Kingdom
Configured Country Codes
        GB  - United Kingdom : 802.11a Indoor,Outdoor/ 802.11b / 802.11g

Hall of Fame Super Gold

Re: Issue in joining 2602i to 3850 wlc

Duplicate posts.  Go here and here.

1181
Visitas
0
ÚTIL
6
Respuestas