cancelar
Mostrar resultados para 
Pesquisar em vez de 
Queria dizer: 
Comunicados
Bem-vindo à Comunidade de Suporte da Cisco, gostaríamos de ter seus comentários.

Problemas com AIR-CAP3602E-E-K9

Boa noite,

Preciso configurar um ap 3602e, para o juntar a uma rede. Acontece que quando tento introduzir comandos, usando o putty como CLI, reconhece o comando enable, mas a partir daí, todos os comandos dão erro de sintaxe. Além do mais, entra em loop, sempre a dar dois erros do Capwap, eu não sendo técnico cisco, acabo por não entender todas as mensagens e siglas que são dadas pelo ap. Deixo o log para apreciação! Preciso mesmo de ajuda, se alguém me puder só dar uma dica sobre qual os tipos de comandos que tenho de utilizar nesta versão do IOS, eu agradecia mesmo muito!

 

IOS Bootloader - Starting system.

flash is writable

FLASH CHIP:  Macronix Mirrorbit (00C2)

Xmodem file system is available.

flashfs[0]: 35 files, 8 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31997952

flashfs[0]: Bytes used: 11196928

flashfs[0]: Bytes available: 20801024

flashfs[0]: flashfs fsck took 15 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: b8:38:61:fa:ff:20

Ethernet speed is 100 Mb - FULL Duplex

Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-mx.152-2.JA"...#########################

 

File "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-mx.152-2.JA" uncompressed and installed, entry point: 0x2003000

executing...

 

Secondary Bootloader - Starting system.

Xmodem file system is available.

flashfs[0]: 35 files, 8 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31997952

flashfs[0]: Bytes used: 11196928

flashfs[0]: Bytes available: 20801024

flashfs[0]: flashfs fsck took 8 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: b8:38:61:fa:ff:20

Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA'

Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...############################

File "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA" uncompressed and installed, entry point: 0x2003000

executing...

 

              Restricted Rights Legend

 

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

 

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

 

 

 

Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Thu 23-Aug-12 02:29 by prod_rel_team

 

Initializing flashfs...

 

flashfs[3]: 35 files, 8 directories

flashfs[3]: 0 orphaned files, 0 orphaned directories

flashfs[3]: Total bytes: 31997952

flashfs[3]: Bytes used: 11196928

flashfs[3]: Bytes available: 20801024

flashfs[3]: flashfs fsck took 9 seconds.

flashfs[3]: Initialization complete.

flashfs[4]: 0 files, 1 directories

flashfs[4]: 0 orphaned files, 0 orphaned directories

flashfs[4]: Total bytes: 12257280

flashfs[4]: Bytes used: 1024

flashfs[4]: Bytes available: 12256256

flashfs[4]: flashfs fsck took 0 seconds.

flashfs[4]: Initialization complete....done Initializing flashfs.

 

Warning:  the compile-time code checksum does not appear to be present.

 

Radio0  present 8764 8000 0 A8000000 A8010000 0

Rate table has 244 entries (64 SGI/104 BF variants)

 

Radio1  present 8764 8000 0 88000000 88010000 4

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

 

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

 

If you require further assistance please contact us by sending email to

export@cisco.com.

 

 

Warning:  the compile-time code checksum does not appear to be present.

 

%Error opening flash:/ap3g2-rcvk9w8-mx/info (No such file or directory)cisco AIR-CAP3602E-E-K9    (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.

Processor board ID FCZ1715Z03L

PowerPC CPU at 800Mhz, revision number 0x2151

Last reset from power-on

LWAPP image version 7.3.1.73

1 Gigabit Ethernet interface

2 802.11 Radios

 

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: B8:38:61:FA:FF:20

Part Number                          : 73-14521-02

PCA Assembly Number                  : 800-37501-02

PCA Revision Number                  : A0

PCB Serial Number                    : FOC170578HY

Top Assembly Part Number             : 800-35874-02

Top Assembly Serial Number           : FCZ1715Z03L

Top Revision Number                  : A0

Product/Model Number                 : AIR-CAP3602E-E-K9

% Please define a domain-name first.

 

 

Press RETURN to get started!

 

 

*Mar  1 00:00:10.147: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed

*Mar  1 00:00:13.635: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar  1 00:00:17.195: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0

*Mar  1 00:00:23.455: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1

*Mar  1 00:00:25.851: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Thu 23-Aug-12 02:29 by prod_rel_team

*Mar  1 00:00:25.851: %SNMP-5-COLDSTART: SNMP agent on host APb838.61fa.ff20 is undergoing a cold start

*Mar  1 00:00:26.171: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Mar  1 00:00:26.171: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Mar  1 00:00:26.175: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source

*Mar  1 00:00:26.183: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully

 

*Mar  1 00:00:26.311: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:00:26.311: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up

*Mar  1 00:00:26.899: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

*Mar  1 00:00:27.351: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Mar  1 00:00:28.339: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Mar  1 00:00:28.427: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up

*Mar  1 00:00:28.435: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down

*Mar  1 00:00:28.443: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Mar  1 00:00:29.427: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up

*Mar  1 00:00:29.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Mar  1 00:00:29.463: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up

*Mar  1 00:00:29.699: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed

*Mar  1 00:00:29.699: DPAA Initialization Complete

*Mar  1 00:00:29.699: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited

*Mar  1 00:00:30.463: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Mar  1 00:00:30.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance

*Mar  1 00:00:54.707: Logging LWAPP message to 255.255.255.255.

 

*Mar  1 00:00:59.803: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.167, mask 255.255.255.0, hostname APb838.61fa.ff20

 

Translating "CISCO-CAPWAP-CONTROLLER.lan"...domain server (192.168.1.254)

 

*Mar  1 00:01:10.751: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:01:10.755: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.lan

Not in Bound state.

*Mar  1 00:02:06.255: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

*Mar  1 00:02:09.275: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar  1 00:02:09.327: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.167, mask 255.255.255.0, hostname APb838.61fa.ff20

 

Translating "CISCO-CAPWAP-CONTROLLER.lan"...domain server (192.168.1.254)

 

*Mar  1 00:02:17.255: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:02:17.259: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.lan

 

Agradeço desde já a disponibilidade para o problema!!!

Marcas (3)
73
Apresentações
0
Útil
0
Respostas
CriarFaça o para criar o conteúdo