Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco IOS XR Remove comment

Folks,

 

Any idea how to remove this from the config?

 

router isis backbone
 set-overload-bit on-startup 180
 is-type level-2-only
 ! ISIS network number should be encoded with 0-padded loopback IP
 ! example:
 ! example:

 net 49.0001.1921.2022.0222.00

 

I tried this, but to no avail...

RP/0/RSP0/CPU0:edge1(config)#clear comm
comment  community-set  
RP/0/RSP0/CPU0:edge1(config)#router isis backbone
RP/0/RSP0/CPU0:edge1(config-isis)#clear comment
RP/0/RSP0/CPU0:edge1(config-isis)# ! ISIS network number should be encoded with 0-padded loopback IP

 

 

 

 

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Hi,

Hi,

 

It looks like you are hitting CSCum68626

 

Symptom:
The IOS-XR parser allows comments (Begun with !) to be added to an ACLs, interfaces etc.

They appear before the ACL, interface etc. in the 'show running-config' output and there is no way to remove the comments, unless you remove and reapply the associated ACL, interface etc.

Conditions:

Workaround:
Remove section of configuration, commit the changes and reapply without the comment.

<B>Further Problem Description:</B>

 

 

Unfortunately due to the nature of the issue we will be unable to fix it, we would have to do a major overhaul of our parser in order to fix the issue.

 

Thanks,

Sam

6 REPLIES
Cisco Employee

Hi,

Hi,

 

It looks like you are hitting CSCum68626

 

Symptom:
The IOS-XR parser allows comments (Begun with !) to be added to an ACLs, interfaces etc.

They appear before the ACL, interface etc. in the 'show running-config' output and there is no way to remove the comments, unless you remove and reapply the associated ACL, interface etc.

Conditions:

Workaround:
Remove section of configuration, commit the changes and reapply without the comment.

<B>Further Problem Description:</B>

 

 

Unfortunately due to the nature of the issue we will be unable to fix it, we would have to do a major overhaul of our parser in order to fix the issue.

 

Thanks,

Sam

Cisco Employee

Wanted to add a few more

Wanted to add a few more things to this. I didn't accept the close of this ddts and want to see it fixed.

A sw solution is beng worked on for this problem. Next time you check you'll see the DDTS in a non close state.

Although the workaround to remove the associated config portion is doable, it is not ultimate.

More to follow on this.

regards

xander

Xander Thuijs CCIE #6775 Principal Engineer ASR9000, CRS, NCS6000 & IOS-XR
New Member

Thank you Xander. I would

Thank you Xander. I would agree that removing ISIS in order to remove some comment lines is not ideal! :)

New Member

Xander,Just wondering if this

Xander,

Just wondering if this was ever resolved.  We are seeing this behavior on our ASR9K's running 5.3.1.

 

-Marc Russo
 

Cisco Employee

yup it is, here is how to:

yup it is, here is how to:

 

"Clear comment" CLI helps to Clear the comment from config line (to be entered next)

RP/0/0/CPU0:ios(config-if)#do show run
Fri May 22 12:04:24.186 IST
Building configuration...
!! IOS XR Configuration 0.0.0
!! Last configuration change at Fri May 22 12:04:18 2015 by UNKNOWN
!
logging console debugging
!comment for intf
interface GigabitEthernet0/0/0/0
 !commemt for mtu
 mtu 100
 shutdown
!
!comment support for Gig interface
interface GigabitEthernet0/0/0/1
 !Mtu comment
 mtu 123
 shutdown
!
interface GigabitEthernet0/0/0/2
 shutdown
!
interface GigabitEthernet0/0/0/3
 shutdown
!
interface GigabitEthernet0/0/0/4
 shutdown
!
router pim
 address-family ipv4
  interface GigabitEthernet0/1/0/24
   enable
  !
 !
!
end

RP/0/0/CPU0:ios(config-if)#clear comment ?
  <cr>  Clear the comment from config line (to be entered next)
RP/0/0/CPU0:ios(config-if)#clear comment
RP/0/0/CPU0:ios(config-if)#mtu 100
RP/0/0/CPU0:ios(config-if)#commit
Fri May 22 12:05:08.201 IST
RP/0/0/CPU0:May 22 12:05:08.315 : config[66191]: %MGBL-CONFIG-6-DB_COMMIT : Configuration committed by user 'UNKNOWN'. Use 'show configuration commit changes 1000000005' to view the changes.
RP/0/0/CPU0:ios(config-if)#do sh run
Fri May 22 12:05:13.939 IST

Building configuration...
!! IOS XR Configuration 0.0.0
!! Last configuration change at Fri May 22 12:05:08 2015 by UNKNOWN
!
logging console debugging
!comment for intf
interface GigabitEthernet0/0/0/0
 mtu 100
 shutdown
!
!comment support for Gig interface
interface GigabitEthernet0/0/0/1
 !Mtu comment
 mtu 123
 shutdown
!
interface GigabitEthernet0/0/0/2
 shutdown
!
interface GigabitEthernet0/0/0/3
 shutdown
!
interface GigabitEthernet0/0/0/4
 shutdown
!
router pim
 address-family ipv4
  interface GigabitEthernet0/1/0/24
   enable
  !
 !
!
end

RP/0/0/CPU0:ios(config-if)#exit
RP/0/0/CPU0:ios(config)#clear
RP/0/0/CPU0:ios(config)#clear comment
RP/0/0/CPU0:ios(config)#interface GigabitEthernet0/0/0/0
RP/0/0/CPU0:ios(config-if)#
RP/0/0/CPU0:ios(config-if)#commit
Fri May 22 12:05:34.642 IST
RP/0/0/CPU0:May 22 12:05:34.750 : config[66191]: %MGBL-CONFIG-6-DB_COMMIT : Configuration committed by user 'UNKNOWN'. Use 'show configuration commit changes 1000000006' to view the changes.
RP/0/0/CPU0:ios(config-if)#do sh run
Fri May 22 12:05:36.945 IST
Building configuration...
!! IOS XR Configuration 0.0.0
!! Last configuration change at Fri May 22 12:05:34 2015 by UNKNOWN
!
logging console debugging
interface GigabitEthernet0/0/0/0
 mtu 100
 shutdown
!
!comment support for Gig interface
interface GigabitEthernet0/0/0/1
 !Mtu comment
 mtu 123
 shutdown
!
interface GigabitEthernet0/0/0/2
 shutdown
!
interface GigabitEthernet0/0/0/3
 shutdown
!
interface GigabitEthernet0/0/0/4
 shutdown
!
router pim
 address-family ipv4
  interface GigabitEthernet0/1/0/24
   enable
  !
 !
!
end

RP/0/0/CPU0:ios(config-if)#root
RP/0/0/CPU0:ios(config)#clear comment
RP/0/0/CPU0:ios(config)#interface GigabitEthernet0/0/0/1
RP/0/0/CPU0:ios(config-if)#commit
Fri May 22 12:05:54.630 IST
RP/0/0/CPU0:May 22 12:05:54.765 : config[66191]: %MGBL-CONFIG-6-DB_COMMIT : Configuration committed by user 'UNKNOWN'. Use 'show configuration commit changes 1000000007' to view the changes.
RP/0/0/CPU0:ios(config-if)#do show run
Fri May 22 12:06:00.620 IST
Building configuration...
!! IOS XR Configuration 0.0.0
!! Last configuration change at Fri May 22 12:05:54 2015 by UNKNOWN
!
logging console debugging
interface GigabitEthernet0/0/0/0
 mtu 100
 shutdown
!
interface GigabitEthernet0/0/0/1
 !Mtu comment
 mtu 123
 shutdown
!
interface GigabitEthernet0/0/0/2
 shutdown
!
interface GigabitEthernet0/0/0/3
 shutdown
!
interface GigabitEthernet0/0/0/4
 shutdown
!
router pim
 address-family ipv4
  interface GigabitEthernet0/1/0/24
   enable
  !
 !
!
end

RP/0/0/CPU0:ios(config-if)#root
RP/0/0/CPU0:ios(config)#interface GigabitEthernet0/0/0/1
RP/0/0/CPU0:ios(config-if)#clear comment
RP/0/0/CPU0:ios(config-if)#mtu 123
RP/0/0/CPU0:ios(config-if)#commit
Fri May 22 12:06:19.356 IST
RP/0/0/CPU0:May 22 12:06:19.481 : config[66191]: %MGBL-CONFIG-6-DB_COMMIT : Configuration committed by user 'UNKNOWN'. Use 'show configuration commit changes 1000000008' to view the changes.
RP/0/0/CPU0:ios(config-if)#do show run
Fri May 22 12:06:21.332 IST
******Nvgen cliend pid: 6833 spawned by pid 25231***********
Building configuration...
!! IOS XR Configuration 0.0.0
!! Last configuration change at Fri May 22 12:06:19 2015 by UNKNOWN
!
logging console debugging
interface GigabitEthernet0/0/0/0
 mtu 100
 shutdown
!
interface GigabitEthernet0/0/0/1
 mtu 123
 shutdown
!
interface GigabitEthernet0/0/0/2
 shutdown
!
interface GigabitEthernet0/0/0/3
 shutdown
!
interface GigabitEthernet0/0/0/4
 shutdown
!
router pim
 address-family ipv4
  interface GigabitEthernet0/1/0/24
   enable
  !
 !
!
end

RP/0/0/CPU0:ios(config-if)#

xander

Xander Thuijs CCIE #6775 Principal Engineer ASR9000, CRS, NCS6000 & IOS-XR
New Member

Thank you Sam. I removed the

Thank you Sam. I removed the net id and reapplied it, which happened to resolve my issue.

 

1079
Views
5
Helpful
6
Replies
CreatePlease login to create content