Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

CRS-1 boot failed problem ( REDFS-5-INIT_FAILED)

Hi expert ,

today I face new problem with one RP , :

Initializing DDR SDRAM...found 4096 MB

Initializing ECC on bank 0

Initializing ECC on bank 1

Initializing ECC on bank 2

Initializing ECC on bank 3

Turning off data cache, using DDR for first time

Initializing NVRAM...

Testing a portion of DDR SDRAM ...done

Reading ID EEPROMs ...

Initializing SQUID ...

Initializing PCI ...

PCI0 device[1]: Vendor ID 0x10ee

PCI0 device[1]: Device ID 0x300e

PCI1 device[1]: Device ID 0x1100

PCI1 device[1]: Vendor ID 0x1013

PCI1 device[2]: Device ID 0x680

PCI1 device[2]: Vendor ID 0x1095

PCI1 device[3]: Device ID 0x5618

PCI1 device[3]: Vendor ID 0x14e4

Configuring MPPs ...

Configuring PCMCIA slots ...

System Bootstrap, Version 1.53(20090311:225342) [CRS-1 ROMMON],

Copyright (c) 1994-2009 by Cisco Systems, Inc.

Acquiring backplane mastership ........failed

Board type is 0x100002 (1048578)

Switch 0 initialized

Backplane FE port Up... Enabling

Enabling watchdog

G4(7457-NonSMP-MV64360 Rev 4) platform with 4096 MB of main memory

..

..

Acquiring backplane mastership....failed.

Unable to access backplane ... invoking READ EEPROM protocol

Enabling only inter-RP port... successful

Sending backplane ID EEPROM read request

Our MAC address is 0249.4450.0008

Interface link changed state to UP.

Sending ID EEPROM read request.

HIT CTRL-C to abort

ID EEPROM read request successful.

Reconfiguring switches with default config ...

Chassis type: 484

    CARD_RACK_NUMBER: 0

    CARD_SLOT_NUMBER: 0

        CPU_INSTANCE: 1

  RACK_SERIAL_NUMBER: TBM13332678    

MBI Validation starts ...Our MAC address is 001e.1392.84ee

Interface link changed state to UP.

Interface link state up.

MBI validation sending request.

HIT CTRL-C to abort

MBI validation sending request.

HIT CTRL-C to abort

mbi_val_process_packet: received response.

RACK_NUM = 0, RACK_TYPE=0

Local image to boot : bootflash:disk0/hfr-os-mbi-3.8.2/mbihfr-rp.vm

boot: booting from bootflash:disk0/hfr-os-mbi-3.8.2/mbihfr-rp.vm

..

.................................................................................

#################################################

tracelogger: starting tracing in background ring mode

tracelogger running with args: -startring -F 1 -F 2

               Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS XR Software for the Cisco XR HFR, Version 3.8.2

Copyright (c) 2009 by Cisco Systems, Inc.

This (D)RP Node is not ready or active for login /configuration

This (D)RP Node is not ready or active for login /configuration

RP/0/RP0/CPU0:Jan 15 09:28:36 : redfs_svr[83]: %OS-REDFS-5-INIT_FAILED : Failed to initialize no devices available: 0x13:No such device

and reboot again , I disabled WATCHDOG but nothing happen,?

this is the show platform from RP0

RP/0/RP1/CPU0:BGD-JAD-PGW1#sh plat

Wed Jan 15 12:08:50.549 Iraq

[KNode            Type            PLIM            State           Config State

-----------------------------------------------------------------------------

0/0/CPU0        MSC             Jacket Card     IOS XR RUN      PWR,NSHUT,MON

0/0/0           MSC(SPA)        10X1GE          OK              PWR,NSHUT,MON

0/0/1           MSC(SPA)        1x10GE          OK              PWR,NSHUT,MON

0/0/2           MSC(SPA)        10X1GE          OK              PWR,NSHUT,MON

0/0/4           MSC(SPA)        1x10GE          OK              PWR,NSHUT,MON

0/RP0/CPU0      RP(Standby)     N/A             MBI-BOOTING     PWR,NSHUT,MON

0/RP1/CPU0      RP(Active)      N/A             IOS XR RUN      PWR,NSHUT,MON

thanks alot

Everyone's tags (3)
2 REPLIES
Hall of Fame Super Gold

CRS-1 boot failed problem ( REDFS-5-INIT_FAILED)

Duplicate posts. 

Go here:  https://supportforums.cisco.com/thread/2260981

Cisco Employee

CRS-1 boot failed problem ( REDFS-5-INIT_FAILED)

From RP1 please capture:

- show context

- show reboot history location 0/rp0/cpu0

thanks,

rivalino

514
Views
0
Helpful
2
Replies
CreatePlease to create content