Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1926087members
1237445discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

My Cisco Nexus Swith 6001 is stuck in bash mode

My Cisco Nexus Swith 6001 is stuck in bash mode and giving below error.system is coming up.....please wait.......This issue happens after power outage happened. We have reboot switch many times and used multiple username/passwords but its not appeari...

WLC 9800 Process iosd Eror

hello,i'm running wlc9800-40 17.6.4 version and i'v got this errorSeverityProcess NameMessageCriticaliosdApr 10 23:47:04.326: %IOSXE_QFP-2-LOAD_RECOVER: Slot: 0, QFP:0, Load 45% recovered.5 secs traffic rate on QFP: Total Input: 13034 pps (13.0 kpps)...

RoeyF by • Level 1
  • 246 Views
  • 14 replies
  • 0 Helpful votes

Redundancy Over VSAT Link

Hi, we have a WAN and VSAT connection to one of the site. WAN is primary and VSAT is secondary link.We have dedicated router for WAN and VSAT. VSAT link is connected to one of the LAN access switch.Could you please help me, what kind of configuration...

inhamit_0-1713245875089.png
inhamit by • Level 1
  • 17 Views
  • 0 replies
  • 0 Helpful votes

WebEx Audio not working on CarPlay

a. I initiate a WebEx call on my phone (through WebEx App).  Audio is working fine.  I then plug in the USBc cable into my phone, CarPlay comes up on the car display.  I see the call UI on the car display, but no audiob. I initiate a WebEx call from ...

bnsrini by • Level 1
  • 247 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Cisco Switch 1000 24port にリプレースしてからネット接続が遅くなった。

<主訴>日中に20%程度のPCがネットに接続できなくなる。アクセスできても、遅い。<社内システム概要>-2024年2月にNetgearのL3スイッチから、Cisco Switch 1000 24port (1Gbpsのポート）にリプレース-8Fフロアのビルで従業員 500名、PC 500台となる。-Cisco Swich 1000 24をL3 Core Switchとして運用している。-スタティックルーティングを利用している。（RIPやOSPFなどは使っていない）-Coreスイッチは、1台構成と...

スクリーンショット 2024-04-12 103928.png
k-system by • Level 1
  • 125 Views
  • 1 replies
  • 0 Helpful votes

QOS for a Destination-ip in Cisco IOSXE

Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...

9800 Guest Anchor Design

I am trying to understand Guest Anchoring with the 9800 Controllers. In the 5500 series WLCs you had to access the WMI from the inside network through the firewall to the Anchor Controller Mgmt Vlan on a DMZ.  Then create another sub-interface on the...

VRRP issue

Facing issue with VRRP, when upstream router5 initiate traffic for downstream router6 then return traffic is not following VRRP VIP as Gateway. In my case switch2 is master and switch3 is standby.If Router6 initiate the traffic then VRRP working fine...

Recommendation Software ISE

Hi EveryoneOur client for ISE software still uses version 2.6 with pach 10,We will upgrade the software to 3.1 with patch 8, please provide a recommendation link from CiscoI'm afraid that if I downloaded it wrong it would have fatal consequencesThank...

Why VLANs are not being shown?

Greetings!So I was practicing to configure VTP and VLANs. For a start, I created 3 switches (only 2 being turned on). The trunks are working fine as the switches are able to acquire an IP addresses via dhcp from a dedicated router and vtp appears to ...

vlans.png
turtle666 by • Level 1
  • 57 Views
  • 1 replies
  • 0 Helpful votes

Alternating ring

Our old work phones would take turns around the room. I don't think it was called hunt group, but once logged in to your group/extension...it would go around the room on whose turn it was to answer. Is there a way to do that? Thanks 

Load more
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: