Cisco Community

Entitlement file generation failed. Please try again.

I am attempting to redeploy our Collector appliance and get the following message. Entitlement file generation failed. Please try again. If the issue persists, find help in the community. From what I have read it seems to be an account issue. Can som...

Can not start Umbrella SWG agent

We have deployed Secure Client with Umbrella module to a few selected users, however i want to enable SWG for the roaming computers and enabled it but i can't start the Umbrella SWG agent service on the PCs.I get the following error as attached pictu...

ASA routing protocols?

Looking for recommendations for routing traffic from ASA back to router on "inside" network so we do not have to add static routes on systems. We recently added an ASR1001 to our "inside" network that routes traffic to Amazon thru a Megaport link tha...

Cisco 9200 Stackwise Modules Hot Swappable

Hi, I currently have a Cisco 9200 switch that does not have a stackwise module at the back. This switch is currently powered on and I am wondering if I can just leave it running and install a stackwise module? Once I added the stackwise module at the...

BGP session wont come up after link goes down - NX-OS

Hello im doing some tests running nx-os 9000v in CML, and whenever i bring down the link running bgp between the two peers i can see in the packet capture that they do not even try to send bgp updates / hellos when enabling the interface again, its n...

why router is choosing iBGP over eBGP?

Why is my router choosing iBGP over eBGP? I am advertising the same prefix in a lab from the iBGP router(RR client) and from eBGP neighbor. Below are the attributes Key AttributesWeight: defaults to 0 for both paths.Local Preference: Both have a loca...

Ise PAN Question

HiIf I need to promote my Sec PAN to Primary PAN due to the PRI PAN being stuck in initilizing, does the promotion cause the ise restart on all nodes or just the Sec PAN Node.?? Thanks

Radius server with L2 switches

Hello, I would need your help.I have scheme, where i have Layer 3 Switch with Windows server controling radius connections, but i want to add Layer 2 swtiches under the L3 one. What should i type in these?

UCCX Upgrade from 11.6.2 to 12.5(SU3) Failing

I am upgrading from 11.6.2 to 12.5(SU3), and all the cop files took on both the PUB and SUB. I was also able to get the 12.5 image file downloaded and installed successfully on both servers, however when I go to switch versions, I get an error statin...

Dot1X AAA issue

%DOT1X-5-FAIL: Switch 1 R0/0: sessmgrd: Authentication failed for client (0076.861a.2790) with reason (AAA Server Down) on Interface Gi1/0/17 AuditSessionID 099FA8C00000001E973BE640 Username: CP-7821-SEP0076861A2790May 20 18:21:18.739: %DOT1X-5-RESUL...

Fast buy dial out on MGCP Analog Station

Built a home lab and working to get my CLCOR, having a problem getting a 2901 with a VIC3-4FXS/DID working for an analog phone. Currently the phone can be dialed but gets fast busy after interdigit timeout. Station is built as a POTs, other choices ...

Missing Recipient

We are seeing quite a few emails in message tracking that are missing the recipient and subject. Any ideas on why this would be happening?

Flexconfig for WCCP on FMC Access List Deployment Issue

We have 2x FTD 2140 Firewalls Managed by FMC that I am trying to get a flexconfig setup for WCCP to use for our Cisco WSA Web Filter. This should be a pretty simple configuration as I am just wanting to put the following 2 commands in via Flexconfig...

la herramienta de eliminación está bloqueada

Acabo de comenzar una evaluación final de ITN Packet Tracer para el curso CCNA-1. Coloqué un cable incorrecto en su lugar, lo que me permitió hacer, y ahora, Packet Tracer no me permite eliminar el cable.Dice "la herramienta de eliminación está bloqu...

Enable midcall signaling in CUCM n have CUCM IP in 200 SDP OK in c

I have a SIP trunk from a third-party PBX to CUCM which has one way audio.When SIP/SDP invite is sent to CUCM IP, we see a rogue RTP stream coming from IP phone directly to third-party PBX in Wireshark capture. This is even before we received 200 SDP...

Meet the Cisco Community team at #CiscoLive 2024!

April Community Updates

Influence the Cisco technology and experiences you use.

Community Activity