The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi all-I have an old 6509 with a SUP720 that I seem to have killed. I was trying to upgrade the code.Before the reboot, she file systems looked like this:and the sup-bootdisk: directory looked like this:I changed the boot line in the config from b...
Busco AyudaAlguien sabe por que no me llega ningun correo de verificación o confirmación al correo con el que hice el curso de ciberseguridad luego de abrir una cuenta en credly, teniendo en cuenta que son los mismos y por consiguiente no puedo recla...
Dear community, I have integrated Cisco ISE and AMP with intention to leverage threat centric data in authorization rules. I can see threat centric data and compromised endpoint within the ISE after executing false-exploit, like status "Painful", etc...
Hi,When overriding certain wifi settings for a particular site in DNA Center, these changes creates a unique profile that is pushed to the wlc.How would i inherit back the global settings for this site?
hello Experts,Please help me regarding VTP Server config on 3560E.I have configure multiple vlans on both the core swithces below is the example, my question is how will be my VTP server configuration on the 3560E since both the core switches will ha...
Hello, I have several boxes configured, but one in specific does not synchronize with the information entered in viptela, when trying to change it to controller mode I have this error log, I have already invalidated its certificate and deleted it, ...
hi,is it possible to configure two vpc peer-link (port-channel trunk) between two N9K?i.e. port-channel 1 would be a temporary trunk and uses MM fiber cable and port-channel 2 would be the 40GBASE-CR4 pre-fab direct cable.the 40GBASE-CR4 would arrive...
Hey community, I have a 3-tier architecture, with 4 VLANs 10-40, I configured inter-VLAN routing on distribution switches and it's working fine, however when I pursued to configure DAI on access and distribution switches inter-VLAN routing is not wor...
Hey!I'm trying to add a NAT rule to my ISR 4321 (Cisco IOS XE Software, Version 17.03.05) for an IPSec VPN running on an ASA 5515-X, but I am receiving the following message. I'm not running IPSec on the ISR as far as I'm aware. Any ideas? isr4321(co...
Hello everyone, Could anyone explain me, please, about the difference between Egress and Ingress PCC. While reading RFC about the PCEP protocol can't catch the real meaning of these two terminologies. Thank you in advance!
Hello all, I need your help to come up with a solution.A user is connected remotely to host location via flex Anyconnect remote vpn(vpn pool - 172.17.1.1 to 172.17.1.40). And also, there is a site to site VPN between the host location(192.168.1.0/24)...
Hi there, i got Cisco Firepower eStreamer Disconnected unexpectedly. i don't setting anything for this eStream, but unfortunately i got disconnected. but my CEF via AMA successfully connected. i try to run "./encore.sh test" and it say success. Also...
I have created a tunnel-te from xrv16 to csr3, the tunnel is up and getting Pop label to csr3 that's ok.From xrv16 I have learned the route to xrv17 over the tunnel, but checking the Label it's unlabbled as well.I believe the route from xrv16 to xrv1...
Good day everyone, I am interested in Segment Routing WECMP. I've searched about load balancing in Segment Routing and found that there is a formula by which load balancing calculates. But i didn't find the logic that on which information it load bal...