Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1926106members
1237515discussions

Community Activity

9800 Guest Anchor Design

I am trying to understand Guest Anchoring with the 9800 Controllers. In the 5500 series WLCs you had to access the WMI from the inside network through the firewall to the Anchor Controller Mgmt Vlan on a DMZ.  Then create another sub-interface on the...

Why VLANs are not being shown?

Greetings!So I was practicing to configure VTP and VLANs. For a start, I created 3 switches (only 2 being turned on). The trunks are working fine as the switches are able to acquire an IP addresses via dhcp from a dedicated router and vtp appears to ...

vlans.png
turtle666 by Level 1
  • 76 Views
  • 3 replies
  • 0 Helpful votes

Recommendation Software ISE

Hi EveryoneOur client for ISE software still uses version 2.6 with pach 10,We will upgrade the software to 3.1 with patch 8, please provide a recommendation link from CiscoI'm afraid that if I downloaded it wrong it would have fatal consequencesThank...

VRRP issue

Facing issue with VRRP, when upstream router5 initiate traffic for downstream router6 then return traffic is not following VRRP VIP as Gateway. In my case switch2 is master and switch3 is standby.If Router6 initiate the traffic then VRRP working fine...

WLC 9800 Process iosd Eror

hello,i'm running wlc9800-40 17.6.4 version and i'v got this errorSeverityProcess NameMessageCriticaliosdApr 10 23:47:04.326: %IOSXE_QFP-2-LOAD_RECOVER: Slot: 0, QFP:0, Load 45% recovered.5 secs traffic rate on QFP: Total Input: 13034 pps (13.0 kpps)...

RoeyF by Level 1
  • 279 Views
  • 21 replies
  • 0 Helpful votes

My Cisco Nexus Swith 6001 is stuck in bash mode

My Cisco Nexus Swith 6001 is stuck in bash mode and giving below error.system is coming up.....please wait.......This issue happens after power outage happened. We have reboot switch many times and used multiple username/passwords but its not appeari...

SSID not discoverable by laptop in Packet Tracer

We have configured two Lightweight Access Points using a 3504 WLC. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Authentication for ...

cmonte0247 by Community Member
  • 56 Views
  • 1 replies
  • 0 Helpful votes

Redundancy Over VSAT Link

Hi, we have a WAN and VSAT connection to one of the site. WAN is primary and VSAT is secondary link.We have dedicated router for WAN and VSAT. VSAT link is connected to one of the LAN access switch.Could you please help me, what kind of configuration...

inhamit_0-1713245875089.png
inhamit by Level 1
  • 55 Views
  • 1 replies
  • 0 Helpful votes

Troubleshoot faulty switchport

Hi,I have a C9200L-48P switch with 4x1G uplink module.Port Gi1/1/1 does not have an LED blinking when connected to another switch.Ports Gi1/1/2-4 seem to work fine.Could anyone please guide me on troubleshooting the port and also advise action?  

Ranjita by Level 1
  • 35 Views
  • 2 replies
  • 0 Helpful votes

UDP-liikenteen leviäminen

Lähetän UDP-liikennettä isäntien välillä reitittimen ja reitittimen välisen linkin kautta. Käytin Wiresharkia ja näen linkin liikenteen, mutta se ei pääse kohdeverkkoon. Käytin Wiresharkia reitittimen lähtöliikenteen skannaamiseen kohdeverkossa, mutt...

headeda by Level 1
  • 22 Views
  • 0 replies
  • 0 Helpful votes

Can't ping from Cisco ASA 5505

I'm currently having trouble with a packet tracer project. I can't ping the s0/1/0 (10.1.1.1) interface on Router 0 from my Cisco ASA device. If you can take a look at my project to see what I am doing wrong any help would be greatly appreciated.I en...

jchain by Level 1
  • 70 Views
  • 1 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: