Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1926937members
1239309discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

IPSec VPN Tunnel Lan-to-Lan decrypt count zero

Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...

El Rondo by • Level 1
  • 352 Views
  • 17 replies
  • 0 Helpful votes

Computers disconnect continuously from WiFi when in office

Our Customer is facing issue on their corporate SSID , We have capture debug and found below logs . Can anyone suggest what can be issue , currently WLC is on IOS 8.5.171.0 and access points connected AIR-CAP3702I-Z-K9.Debug logs apfMsConnTask_3: Apr...

amit.gaur by • Level 1
  • 54 Views
  • 2 replies
  • 0 Helpful votes

CCIE

Hi,I have been curious about CCIE certifications. Does anyone know how many Cisco Certified Internetwork Experts are there and also who has the #1 CCIE certificate? 

m4rlung by • Level 1
  • 67 Views
  • 2 replies
  • 0 Helpful votes

Cisco 2921 for home use

I'm having problems setting up my home network using Cisco2921 for the first time. It has the basic licenses only. Below is the running config followed by my adapter settings. Any assistance would be greatly appreciated. Thank you.Current configurati...

ISP VLAN Tagging

If my ISP is logically routing between a routed interface on their end with an IP in the same subnet as my end's Layer 3 router SVI interface for VLAN 10, but the ckt terminates on a layer 2 switched interface on my end using vlan 10, does my ISP nee...

Tracking network speed

Hi thereI am assigned to check the issues with this attached network and have managed to remove some hups and redesign the network to what it is now. there were no vlans and it has been configured. the issue is that the internet speed is extremely sl...

Can I change the regulatory domain for our new CW9164I-ROW AP?

We have a 9800-CL Wireless Controller running 17.12.2.  We just got a new CW9164I-ROW AP and its registered by the operational interfaces are down due to a regulatory domain error.  Is there a way to change the regulatory domain for the access point?...

A question about MAC addresses for access points

Can anybody tell me what exactly is the difference between the radio MAC address vs the ethernet and Wi-Fi mac addresses? What is the purpose of the radio MAC address? Apparently, wireless access points don't just have an ethernet and Wi-Fi MAC, but ...

HSRP Not Establishing but L2 Connectivity Verified

Replacing some old cisco routers with 8500's running 17.9.4a.  They are connected to a Nexus 7K, on the same card.  The routers can ping one another and establish BGP but they will not establish the HSRP adjacently across the 7K.  If the 8500's are c...

FTD intervlan questioning,

Scenario,Host-A(10.10.30.3/24) connects to access port on SwitchA with various other vlans also configured via access ports. SwitchA connects on a Trunk port to a CatSwitch. Firepower inside ½ interface trunks to CatSwitch. On The CatSwitch 3 vlans; ...

GatLMCO by • Level 1
  • 186 Views
  • 8 replies
  • 0 Helpful votes

Configuring NAT overload with vrf lite on a CAT9K

Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12.  This is what I am struggling with, I currently have a vrf called AWSDX-S3.  Now what I am trying to do is I have added a L2 SW and ran trunk ports...

gurowar by • Level 1
  • 57 Views
  • 2 replies
  • 0 Helpful votes
Load more
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: