Nexus 5500 ethanalizer interrupts

Hi community, I'm trying to collect DHCP packets from a Nexus 5500 and the problem I have is that the capture is interrupted randomly, so I nbeed to keep looking at the console to re-run it again, and some times it takes me some tries to get it worki...

I don't understand how TACACS Profiles works.

If you look at the tacacs profile as shown in the picture, there are custom characteristics I wonder how this works. In the case of other banders, I understand that tacacs are linked using these attributes If you add a value here, compare it with the...

This is happening on my cisco switch 9300

Hi Members, This is happening on my Cisco switch, and I have no idea why this is happening.  Anybody had the same issue? If so, how did you all fix this, please? Your help suggestion and idea would be highly appreciated.       May 1 23:25:19.000: %LI...

C9300L-24T-E machine version 17.3 default padding settings

I am using the C9300L-24T-E machine version 17.3 and was wondering what the padding default settings are?

思科无线 AP 注册不了的问题

无线AP 思科 AIR-AP-1832I-H-K9 无线控制器 思科 2504 只是想测试一下AP的覆盖范围 ，因为没有三层交换机 用了个家用的路由器给提供 DHCP 服务 问题 ：AP能获取到地址 但是注册不了 显示 not joined 日志是怎样的 ，看不明白 ，哪位大大给解释一下到底是什么原因*spamApTask6: Apr 02 15:08:57.103: #DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:818 Failed ...

cisco macsec between my head office and branch offices

cisco 9500 layer 3 switch in the head office and C3560CX switches in 5 branch offices. ISP gives an interface to the head office, both data vlan and internet vlan. I want to establish macsec between the branches.can anyone support me in macsec setup?

CAPWAP do not convert to EWC

Hello,We have Catalyst 9100AX series APs. We want to convert one of them to EWC. We tried to factoy reset both however after the reset they are still act like CAPWAP and stuck at  CAPWAP States.P.S. We have WLCs in our network but we isolated the VLA...

Cisco CBS Switch Latest Firmware Availability

Dear Cisco Community,This is regarding availability of latest firmware for below-listed Cisco CBS Segment Switches. Basically, I'm performing Manual Network Audit where I need to provide a list of latest firmware(s) with date & time stamp of release ...

NAT for ping ICMP from outside to inside via ASAv

Hi, I am 4-year student to university of since from Vietnam. I have a problem about ping ICMP through ASA. I can ping from R2 from outside to 4.0.0.1 of DMZ or 8.0.0.1 of inside. I can ping from DMZ via inside. Can also ping from DMZ and inside to go...

Hotline phone service to be available 24/365

Dear Friends,I would like to know the best design and product (Cisco compatibility) for a hotline phone system. The hotline service should be available 24/7 and without downtime. I need around 150 phones to be installed inside the production factory....

test

How to get to know Cisco FTD 2130 throughput

Hello all, I would like to know how to calculate current throughput value at FTD 2130. What sort of information need to calculate it.? Thanks for any response to solve it. 

No ringing back tone from PSTN (SIP trunk) via CUBE

Hello, I have an issue about ringing back tone when I call from outside --> PSTN (SIP trunk) --> CUBE --> UCCX --> redirect call to extension. I hear IVR and can do DTMF. then press extension, no ringing back tone.However when I call from PSTN (SIP t...

MPLS label type unknown

hello, i have enable netflow in egress interface (mpls) in IOSXR 9922 cisco routerwe see there's MPLS label type "Unknown" in several prefixes /32 (IP loopback router)and i have check by perform this command "show mpls forwarding prefixes (iploopback...

While browsing it can't connect ESA with domain name

Hi,When i try to browse ESA with domain name it is not get connected. But when i put ip address then the ESA login page appeared and we can login. what can be the issue?