Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1927314members
1239968discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Puzzling results when pasting in ACL config to switch

Hello, I was creating 2 decently large ACL's to match some traffic today and I noticed something peculiar that has me puzzled. My first ACL has approx 90 ace's and pastes them fine. When I go back and look at the ACL, it looks like there are only lik...

Creating public space with restrictions

Hi, I would like to create a public space where the members/admins can chat and they are the only ones who can see it and all the others can post and they can see the answers only. I do not know whether it is possible or not. Any thoughts welcome.Tha...

ifulop36 by • Level 1
  • 0 Views
  • 0 replies
  • 0 Helpful votes

uccx - CUIC 12.5.1 - Repors: Chart with abandoned call total

Hello world,I am working on creating a custom report based on the stock reports available for our call center. We would like to total the abandoned call  for each day, sorted by the hour of the day. I cannot seem to create a report that only shows th...

MyaDime by • Level 1
  • 75 Views
  • 2 replies
  • 0 Helpful votes

VPN Troubleshooting

Hello, as part of my preparation for CCNA Security I've been making up my own topologies and configuring them, however, I might need a little help with this one. In the topology (included .pka), I configured VLANs, Port Security, OSPF, OSPF Authentic...

xmorav45 by • Level 1
  • 24 Views
  • 0 replies
  • 0 Helpful votes

IPv6 ping not working when pinging other LAN

I configured the simple network below to test the connectivity of the ipv6 in the devices. The configurations are as shown and ipv6 unicast-routing is enabled. When pinging from Router 5 to Router 6 G0/1, it succeeds but when pinging from Router 5 to...

Webex App support policy Question

The latest post regarding Webex App support https://help.webex.com/en-us/article/ne3khsm/Webex-App-support-policy  states that "To ensure a high level of security and access to the latest features, Webex enforces a limited lifespan for its desktop cl...

Jesse D by • Level 1
  • 125 Views
  • 1 replies
  • 1 Helpful votes

Unable to ping between two tunnel points

Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...

AP-AIR2802i-B-K9 No join

l installed newest version of Wireless controller 9800-CL Cloud but wont Join DTLS Error l dont why it wont join to controller 

lisavbedt by • Level 1
  • 112 Views
  • 8 replies
  • 0 Helpful votes

Configuring NAT overload with vrf lite on a CAT9K

Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12.  This is what I am struggling with, I currently have a vrf called AWSDX-S3.  Now what I am trying to do is I have added a L2 SW and ran trunk ports...

gurowar by • Level 1
  • 137 Views
  • 4 replies
  • 0 Helpful votes
Load more
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: