Cisco Community

QOS for a Destination-ip in Cisco IOSXE

Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...

WLC 9800 Process iosd Eror

hello,i'm running wlc9800-40 17.6.4 version and i'v got this errorSeverityProcess NameMessageCriticaliosdApr 10 23:47:04.326: %IOSXE_QFP-2-LOAD_RECOVER: Slot: 0, QFP:0, Load 45% recovered.5 secs traffic rate on QFP: Total Input: 13034 pps (13.0 kpps)...

DMVPN Spoke not connecting when using starlink

I have set up as above. I am using starlink at one of my spokes. I am not able to get to pass VPN traffic even though show dmvpn shows that the vpn is up.

9800 Guest Anchor Design

I am trying to understand Guest Anchoring with the 9800 Controllers. In the 5500 series WLCs you had to access the WMI from the inside network through the firewall to the Anchor Controller Mgmt Vlan on a DMZ. Then create another sub-interface on the...

VRRP issue

Facing issue with VRRP, when upstream router5 initiate traffic for downstream router6 then return traffic is not following VRRP VIP as Gateway. In my case switch2 is master and switch3 is standby.If Router6 initiate the traffic then VRRP working fine...

Recommendation Software ISE

Hi EveryoneOur client for ISE software still uses version 2.6 with pach 10,We will upgrade the software to 3.1 with patch 8, please provide a recommendation link from CiscoI'm afraid that if I downloaded it wrong it would have fatal consequencesThank...

Why VLANs are not being shown?

Greetings!So I was practicing to configure VTP and VLANs. For a start, I created 3 switches (only 2 being turned on). The trunks are working fine as the switches are able to acquire an IP addresses via dhcp from a dedicated router and vtp appears to ...

how to onboard the SDA Fabric Edge which is using stackwise virtual

Hi , Thank you so much . Does anyone have any idea how to onboard the stackwise virtual into fabric , as of today LAN automation is not supported.Im thinking of below approach , really appreciate your valuable suggestions. 1> Manually configure the...

Alternating ring

Our old work phones would take turns around the room. I don't think it was called hunt group, but once logged in to your group/extension...it would go around the room on whose turn it was to answer. Is there a way to do that? Thanks

WebEx Audio not working on CarPlay

a. I initiate a WebEx call on my phone (through WebEx App). Audio is working fine. I then plug in the USBc cable into my phone, CarPlay comes up on the car display. I see the call UI on the car display, but no audiob. I initiate a WebEx call from ...

destination address is the broadcast address within matched route

Please see attached pic. In this question, the destination address matches the route in the routing table. But it's the broadcast address within that range. Would the packet still be routed with that route?what would the next hop be? 192.168.0.7 or 1...

Simple SSH Connection 9400 Not Working

Is there something different about configuring SSH on a 9407 with a C9400-SUP-1? Currently there's no configuration on the device except for an IP address on the management port and ssh. I've gone through the same procedures we've always used and v...

Catalyst 9000 シリーズスイッチ set ip next-hop verify-availability は非サポート

Catalyst 9000 シリーズスイッチと結線された対向機器の起動時等に、対向機器の不具合や実装により、Catalyst 9000 シリーズスイッチが PBR で使用しているインターフェースが対向機器の起動処理中アップしてしまい、この事に起因しPBR が動作してしまう事により、起動途中のためトラフィック転送ができない対向機器にトラフィックが転送されてしまうようなケースがあります。 Catalyst 9000 シリーズスイッチの PBR では、set ip next-hop verify-a...

Cisco Catalyst 9800-40 Wireless Controller

Hi all,I am new to Cisco WLC.I have Cisco Catalyst 9800-40 Wireless Controller and it is running on software version 17.3.4c.I am told to upgrade to the latest one and I have no idea which is the latest one with no bug in it. I tried to download the ...

Unable to download CML personal

My order number is Order#...6044. I am unable to download CML personal. I purchased this lab on Saturday. I keep getting 503 errors or blank screens. Any assistance would be appreciated. Thanks

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

Introducing Our New Gamification Ranking Naming

Community Activity