The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello,Studying for my CCNA and I thought I'd practice some basic configurations, such as router on a stick. I setup 4 PC's (each representing an imaginary number of hosts) each with a vlan attached to a switch leading to a router, with the link betwe...
Des infos sur un centre à Montréal où je peux faire le CCNA en toute sérénité serait la bienvenue car ci-dessous:Nous sommes désolés, la politique de Cisco interdit la délivrance d'examens au Québec. Pour passer les examens de Cisco vous devrez peut-...
How do I get a response from Lufthansa?Talk to someone on Lufthansa airline smoothly, and give their dedicated support line a ring at +1|ퟴퟱퟱ|ퟱퟮퟲ|ퟬퟯퟬퟳ, for USA +1-ퟴퟱퟱ-ퟱퟮퟲ-ퟬퟯퟬퟳ(UK). Take your time and listen carefully to the automated prompts, then s...
I configured NAT and DHCP relay in GNS3, and all hosts have end-to-end reachability, I can ping PC44 from PC11 and PC22, and also from PC33 if I configure a static IP address.On the NAT router (R11), I also configured DHCP relay with 'helper-address'...
Good morning friends,I have created two extended ACLs for in and out of my int vlan and applied it under int vlan for both directions inbound and outbound. I have created ACLs entries like this.For int vlan no. Out1 permit ip 10.1.0.0 0.0.255.255 hos...
Please see the attached file. When a Windows client connects to the network and its supplicant is configured to send the computer certificate, what exactly is the PSN doing with this certificate? In the attached i have a use of Lab_dot1x_Certs (See...
A simple question....If I just knew where to find the answer:Doing MAC authentication on an 5520 WLC, I can see the MAC addresses accepted by the WLC if I issue the command:"sho macfilter summary"Can anyone tell me the equivalent command on a 9800 (y...
Hi All, I need your assistance to check if the following configuration going to work and are there any drawbacks/caveats?So far I identified OSPF convergence time and impact on a relatively large area 0 *(legacy design). Solution details:I have ACI M...
HelloWe have a lot of clients getting the following error when contacting diffrent sites: ERR_SSL_PROTOCOL_ERROR, we have read that SonicWall and Palo Alto also have these problemes. Solution is to turn off "TLS 1.3 Hybridized Kyber Support" in chro...
Our Forum Alert III Secondary Crash Net (SCN) is inoperable. I've heard the cisco cm could be configured to set up some devices to act as a ringdown, they called it a “Switch Box.” This would allow our Base Operations guys to have a work around from ...
Hi community!I posted about some 2702i in autonomous mode, degrading throughput after some time - see post: Autonomous Mode Failing on Aironet 2702i-z-k9 - Cisco CommunityLast days I got a WLC 2504 and other 2702i access points (in controlled - LWAP...
Hello we have a local 9120axi AP with a 9800LC WLC that seems to be losing connection. The AP is in flex connect, all config looks fine: AdvancedCountry CodeUS Multiple CountriesUSStatistics Timer180CAPWAP MTU1485AP Link LatencyEnabledAP PMK Propaga...
Dear Sir i am new to 8851 ip phone , just need help for speed dial kem i do program speed dial entries into the device and when the phone is turned off the entries are lost is there is any advice why list is forgotten from the phone ? thanks
Hi Experts,I am sitting with an unique issue where my Auto Attendant works perfectly from inside the office, however it is not reachable from external calls.Connection ISP > SIP > CUBE > SIP > CUCMWhat I am seeing is as soon as I direct the call to C...
Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12. This is what I am struggling with, I currently have a vrf called AWSDX-S3. Now what I am trying to do is I have added a L2 SW and ran trunk ports...