The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
I have a customer who uses Cisco SPA502G phones, from 5 months ago in October 2023, they have been complaining that their phones have been rebooting themselves from time to time.The Reboot History under Info page shows that the Reboot Reason was Syst...
Hey All,Anyone know of any tools to migrate config from Palo Alto to Firepower (or better yet, secure device manager)? Needing to migrate 5x physical appliances and 1x virtual rapidly.We need to migrate: DNS (DNS Proxy) DHCP NAT Security zones Interf...
1Gb catalyst switches has air intake from front and side and exhaust to the back. And no versions with reverse-airflow.I know many places where such switches installed port side to the hot corridor - so it intake hot air and blow to direction of col...
We are operating our vehicles remotely in the underground mines over Wi-Fi, the data load from the machine is constant around 30Mbit/s (yes, six to eight HD-cameras).When switching between APs we have noticed that we sometimes get a transmission gap ...
Which IPv6 address range is suitable for anycast addresses for distributed services such as DHCP or DNS?2001:db8:0234:ca3e::1/1282002:db84:3f30:ca84:be76:2/64The first one isn't a range. but people are saying that the second one is invalid. But why?
Hello we have a local 9120axi AP with a 9800LC WLC that seems to be losing connection. The AP is in flex connect, all config looks fine: AdvancedCountry CodeUS Multiple CountriesUSStatistics Timer180CAPWAP MTU1485AP Link LatencyEnabledAP PMK Propaga...
Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question: Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...
Hi all, I have a 3650 stuck in the switch prompt. I've tried to set the IP address using the below commands so that I can upload the IOS, but I am unable to. set IP_ADDR Set DEFAULT_ROUTERbelow is the file system outputswitch: dirList of filesystems ...
Hello all, We have ISE with DNA Center merged. We have a requirement to limit/control the number of users that are allowed to login to DNAC at anyone time. Most Cisco devices can control this but is there a way to do this via ISE RADIUS/TACACS+? I ca...
Hi, Has anyone had issues where you are running FTD with AnyConnect (secureclient) with Posture (DAP) enabled and some computers are sending the attribute endpoint.am=xxx and others aren't? I have several devices not sending the anti-malware attrib...
Hello,I have a Nexus 9K trunked to a C9200LOn the Nexus 9K the port is:interface Ethernet1/19switchportswitchport mode trunkswitchport trunk native vlan 888switchport trunk allowed vlan 1,254,995no shutdownOn the C9200L the port is:interface TenGigab...
I have a 9800-CL in an SD-WAN setup. I have multiple sites that have the same Vlans at each site to make it easier to manage and remember.Ex:NorthSite: data-4, voice-5, wifi-6SouthSite: data-4, voice-5, wifi-6etc...My current WLC configuration has on...
I have some branch locations with a simple set up. A router with an access switch connected to it, then another access switch connected to that one to provide POE to IP phones. Currently all devices are in the same VLAN.I also have an access point co...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: