The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
[[FAQ,S]] How can I get in touch with 헤헮혁헮헿 in the UK?@QUICK~HelpHow can I speak with a live person at 헤헮혁헮헿 헔헶헿현헮혆혀?To talk to a Person at 퐐퐚퐭퐚퐫 Airways for live support, you have options. You can call their customer service hotline 퐐퐚퐭퐚퐫(핆핋픸) ✈+ퟏ-ퟓ...
[[FAQ,S]] How can I get in touch with 헤헮혁헮헿 in the UK?@QUICK~HelpHow can I speak with a live person at 헤헮혁헮헿 헔헶헿현헮혆혀?To talk to a Person at 퐐퐚퐭퐚퐫 Airways for live support, you have options. You can call their customer service hotline 퐐퐚퐭퐚퐫(핆핋픸) ✈+ퟏ-ퟓ...
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
We have configured two Lightweight Access Points using a 3504 WLC. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Authentication for ...
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
My org has a single CUCM cluster with around 10k phones registered across 100+ buildings. We've been semi-regularly experiencing an issue that we've had trouble tracking down. Due to the nature of our deployment and the intermittent/difficult to repr...
The developer’s role in a greener future Developers can optimize software for Cisco devices to reduce their energy consumption. By writing efficient code, developers can minimize the processing power required to perform tasks, thereby lowering the en...
Dear all,I've set manually a specific port, in which have a non-Cisco WiFi 6 Access Point running, to provide 30W to make the PoE+ runs, but the AP itself didn't recgonize the power provided as PoE+.I've adjusted at web interface as well at CLI. Is t...
I have an ISR4431 router, and related setting:ip access-list standard toGCP10 permit 10.136.0.0 0.0.127.25520 permit 10.136.128.0 0.0.127.25530 permit 128.231.0.0 0.0.31.25540 permit 128.231.32.0 0.0.31.255!route-map toGCPmatch ip address toGCP!route...
NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...
I'm running CBD2.7.1 and installed a public wildcard certificate.The following error is flashing on the top of the dashboard:"Server certificate does not contain your server address in Subject Alternative Name."Is this a bug when using wildcard certs...
Hi,FTD was added and to FMC and while configuring HA in FMC, deleted FTD from FMC.While trying to add again to same FMC, both primary and secondary FTD not getting registered in FMC.Could you please help on getting the FTD registered with FMC.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: