The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello,I have a C1300, I use it as my IPv4 and IPv6 gateway for internal routing. It has a default gateway to another router for internet access. If I perform an IPv6 speedtest with the c1300 as my gateway for IPv6 then I get around 1Mb, this is stran...
Deployed a 3100 in chassis mode to the FMC a few days ago. All went to plan.Determined we needed to change the IP so decided just to delete the device from FMC and re-provision it.On the FTD via local-mgmt did a erase configuration. The device wiped ...
Where does one set the FROM e mail address used by CUIC report scheduler to e mail reports? I thought I knew....but it isn't where I thought it was. And I cannot find it in any documentation....
Hi,I am trying to set up an SSH connection to my switch, but right now there is some lower level problem. I have set up my FastEthernet0 interface to ip address dhcp and the command show interfaces FastEthernet0 shows the correct address. Even if I t...
OK, so I've got a set of ASA's and we are migrating them to Firepowers, and all seems ok. In the past we have noticed that for some reason on the ASA's, no matter what you specify as the parameters for phase 1, the rekey timer always connects at 3600...
Hello Everyone, I am new to segment routing. I am trying to learn the dynamic option of segment routing traffic engineering. I have 2 directly connected routers.R1---R2R1's Gi0/0/0/1 IP address 100.10.20.1R2'2 Gi0/0/0/1 IP address 100.10.20.21.1.1.1 ...
Hello everyone,I am a student, and for a paper i am doing i was wondering if Catalyst 9500-16X was able to do VPN IPSEC as a client, connecting to a cloud VPN IPSEC server. The use case is a Collapse Core topology and i would use 2 C9500-16X as the c...
Hi all,I want to ask you experts some suggestion on how really work mechanism between Cisco switches and radius server when using dynamic vlan assignement and the radius suddenly will be unavailable.With server dead command under port configuration i...
My Windows Server Core having an internal address of 192.168.50.2, when natting it (NAT) it has an address of 192.168.99.36 (I'm installing Windows Server Core image on an EVE-NG VM and the EVE-NG VM is installed on ESXi).I have a Cisco ISE VM instal...
Hi we have 2 WSA out of which one WSA is showing 503 error for a specific Site. When i tried nslookup in WSA for that site it shows the server returned no data(in both WSA).But the site is working in one WSA but not in the other and after 15 mins the...
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Hello everybody,our customer has a FMCv running sugg. rel. 7.2.5.1 and has a high CPU load of approx. 97%.(see attached screen dump).The VM has 4 CPUs, 32GB RAM and 250GB HDD.The FMC is managing a HA of two Firepower 1120 running rel. 7.2.5.A FMC reb...
Hello,We got new terminals Honeywell EDA61K, but we have a problem with connection loss.Wireless LAN Controller is Aironet 2800 Series ME. Terminals randomly lose connection. After a while he returns.I switched the WiFi network only to 2.4. This redu...
Don't you just hate having to run RTMT in a virtual machine, well here it runs in an app for mac. I have complied a version for CUCM 14.x ( from a version I got for 11.x ) It works on older versions also. Here it is https://haffi.is/rtmtmac14.zip old...