Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1936657members
1262538discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

vBond routing from WAN Edge

So if you have 2 transports from the WAN Edge, must it have ECMP to vBond in order for vBond to detect the public and private IP of both transports?Say for example you had an MPLS and Public-Internet TLOC. The Public-Internet TLOC is (unwittingly) re...

Cisco Finesse "send error report"

Cisco Unified CCX AdministrationSystem version: 12.5.1.11001-348 (SU1-ES03)Where does one get access to view the error repot that get generated when you click on "send error report" with the Finesse web page? 

ASR BGP problem

the router looks fine and show ip bgp is correctR2 can't reach ISP by going to R1 to ISP*******************************************************************************************************R1no license smart enable!!spanning-tree extend system-id!i...

Resolved! Difference between Default-originate and network 0.0.0.0 in BGP

Hello,   Please i need someone to clarify what is the difference between the "default-originate" command and "network 0.0.0.0 - ip route 0.0.0.0 0.0.0.0 null0" commands. I see both are serving the same purpose by advertising a default route to a pee...

SOME DIAGNOSTIC COMANDS FOR MY NEW C4507

Hiiiiiiiii I have some new equipment, WS C4507R+E and i would like to have some diagnostic commands, hardware, software, CPU, even modules and supervisors, just to certify that everything is fine...  Can someone helpme with some CLI comands plx? 

webex messaging

Is there a report for webex messaging inbound or outbound?  I need date, time and the numbers or emails the message is going to.

MTU on subinterfaces

So normally a standard interface has an MTU of 1500.When creating a sub-interface on a router (or using an SVI on switch), should the MTU be manually lowered to 1496 to account for the extra 4 bytes?Everything just seems to work without this, so I am...

RIp not working

Hello! I am a student at college and i need some help with setup RIP.It is necessary that the network of the entire project be 197.10.19.0/24.Since I was constantly experiencing overlap when using it, I changed the subnet mask to 28.No matter how muc...

Prokhor15 by • Level 1
  • 41 Views
  • 2 replies
  • 0 Helpful votes

Enable/Upgrade IKEv2 [ cisco ISR4451-X/K9 ]

Dear Experts!I have ISR4451-X/K9 & seemed there is no IKEv2 available.Can anyone guide me with steps to upgrade to ikev2?Thanks! 

Yahya by • Level 1
  • 42 Views
  • 1 replies
  • 0 Helpful votes

PDART tool for migration

Dear Community,We're in the process of migrating from Cisco Prime Infrastructure Version 3.10.2 to DNAC Version 2.3.3.7. However, when running the PDART tool, it generates a report for Cisco Prime Infrastructure Version 3.10.0 and DNAC Version 2.3.5....

riveir by • Level 1
  • 16 Views
  • 0 replies
  • 0 Helpful votes

ACI L3out Pair Firewalls

Hey folks,I'm looking to set up an L3out with static routes for an Active/Standby Firewalls pair, as shown in the diagram below. However, I'm feeling a bit confused, especially when it comes to configuring the L3out with SVI. Any advice on how to pro...

atalebzadeh_0-1714918391600.png
Load more