Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
How to Pass the DevNet Specialist - DevOps exam (300-910)
by Alex Stevenson -
CTF: my first post
by mmuench -
ACL configure
by cyberpea -
Help with Jabber contact list import
by sebastian-friedemann -
Should we enable allow-service netconf all the time?
by yutashimamura2920 -
Lock AnyConnect profile to specific certificate
by Crag Muer -
Stop in progress template provisioning
by Gricel -
Interface Vlan administrativamente inativa
by ftoprakw
Community Activity
Can you pls suggest ethernet switch which should support 1G, 2.5G, PTP
Could you pls suggest cisco ethernet switch which should support 1G, 2.5G in RJ45 mode along with TSN, PTP protocol, IEEE 1588
Nexus 9332C Booting ACI image from boot loader issue
Hi Guys, I am looking for some help as I hit obstacles and I think that I have tried all possible options, to get this issue resolved.So I was converting Nexus 9332C from NX-OS mode to ACI mode to version aci-n9000-dk9.14.2.6o.bin and at some point p...
Resolved! ISE Failures - MAB instead of 802.1x
Hello, I've been struggling with an issue in our ISE deployment for months. Basically, we are trying to restrict wired network access for computers by looking for 802.1x and then authorizing if the CA issuer for the machine cert is our internal CA....
Stop in progress template provisioning
Hello everyone. I'm very new to DNAC or Catalyst Center. I've setup a project with a template to add a simple configuration to switches. It currently has been in progress for 10 days and hasn't made a change to a switch yet. I'd like to cancel th...
Trunking an ip addressed inside interface on Firepower 2130
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
PBR on ASA to Interface Without Directly Connected Next Hop
I have an ASA on which I'm trying to use PBR to route to one of two ISPs which I'll call "slow" and "fast." The interface to the slow ISP is connected to a subnet on which the next-hop address is clearly in the subnet and it would count as "directly ...
Interface Vlan administrativamente inativa
Acabei de criar uma vlan, atribuí-la a uma porta em nosso 6509, atribuí à vlan um endereço IP e quando eu disparo o comando, show int vlan 31 ele diz que a vlan está administrativamente inativa. Não consigo descobrir o que está acontecendo aqui? emit...
ITU-T Y.1731 on cisco 9200/9300 switches
Hi, I am working on a RFP where one of the specs says " the switch should support IEEE802.3ah ethernet link OAM and IEEE 802.1ag/ITU-T Y.1731" this is the only point which i am not able to find a reference in cisco documents, though we have a cisco 9...
unknown IPs in FTD outbound logs
I am managing FTD-1120s with FMCv both running v7.2.1 software. In my ACP I have a GEO rule to block all outbound traffic to China, Russia, and I few other "hotspots". When I search for events that match this rule, most of the traffic is from inte...
Max number of licenses available for Cisco ISE
I'm speaking of Essentials/Advantage/Premier. We use on-prem SSM.is there way to know how many licenses Cisco ISE gets from the binding to a virtual account on Cisco SSM?The only piece of information is the consumed ones, like knowing how many you ar...
FMC IP fragmentation to no fragmentation settings can couse outage?
Hello everyone, I have the following issue:The customer would like to disable FMC packet fragmentation globally. According to the Cisco documentation it is quite straightforward.Source chapter: Fragment SettingsCisco Secure Firewall Management Center...
CBS350 Setup guidance
Hello,I have an ISP router/modem, along with assignable public IP addresses for use. Leaving default VLAN1 alone (mgmt), I created VLAN10 (192.168.0.0/24) and VLAN20 (172.16.3.0/24) on the CBS350.ISP router "internal" ip 172.16.2.1/24On CBS350 port G...
Resolved! RRM Power on 6GHz not match between IOS version 17.9.4a and 17.12.3
I've migrated one pair of 9800-80 from 17.9.4a to 17.12.3. I noticed that the APs w/ RRM on the new 17.12.3 on 6GHz have drop drastically up to 8 dBm (see attched picture). Is anyone aware of this change and why on 17.12.3?
CBS350 Firmware 3.4.0.17 POE on Ports shows Fault - Short Counter High
I have several CBS350 switches running 3.4.0.17.They are showing POE faults on some of the ports.I'll use one switch as an example. It is a CBS350-24FP-4G.The POE Properties show Nominal Power = 370WAllocated Power = 13WAvailable Power = 357WSoftware...
Updating Radius server
Hi,If Radius server gets updated with the new IP address, will current users remain connected or will they need to reconnect?I am asking for both AireOS and 9800 WLC.
