Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
BGP-LS ; how is BGP-LS data processed in BGP RIBS
by kandhla chandi -
Trunking an ip addressed inside interface on Firepower 2130
by jreynolds4 -
ssh into a switch - no matching key exchange method found
by fabioairoldi -
Is there a CLI to monitor traffic stats on a l2transport interface?
by ThomasD86 -
Two Mac addresses from the FTD 2110 MGMT interface
by willpkk01 -
L3 Switches connecting to Firewalls
by Ranjita -
Setting UP a SECOND ASA5506-x firewall
by Myleslandish -
Site-to-Site IPSec with VTI - Initial delay up to 60 seconds
by Plamen Mladenov
Community Activity
Policy Based IPSEC Tunnel With Firepower
If I am configuring an IKEv1 IPSEC site-to-site VPN with an FTD device running 7.4.1 managed by the FMC and it is policy based, not route based, does the system ACL applied to the device also control the traffic across the tunnel? If so, then what Zo...
Block Ping
Hello im a beginner in using cisco so my task is admin can ping admin but student cant ping admin.student1(198.140.70.4 255.255.255.248) and student 2 (198.140.70.11 255.255.255.248)admin1(198.140.70.3 255.255.255.248 ) and admin2(198.140.70.10 255.2...
IPSec VPN Tunnel Lan-to-Lan decrypt count zero
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
Resolved! Best way to integrate ASA/ISE/Azure AD for MFA?
I want my VPN users on a Cisco ASA to authenticate against ISE but use Azure AD for MFA on the backend. So far, it seems there are three ways to do this. My requirements are that I must use AnyConnect and ISE. Setup Azure AD as External Radius Server...
Cisco Networking Academy
Soy nuevo en CISCO, estuve interesado en Redes y realice el tema de Conceptos Básicos de Redes. Pero hay un problema en la evaluación final, ya que me aparece "Contenido Bloqueado - El contenido de esta página no es visible porque se encuentra bloqu...
Qual é a diferença entre DTP e VTP?
Se és daqueles que achava que DTP e VTP serviam para o mesmo, deixa-me dizer-te que não estás sozinho. Eles podem ter o nome parecido mas têm funcionalidades distintas. DTP ou Dynamic Trunking Protocol, é um protocolo L2 usado para negociar se duas p...
Static Routes on FTD 2130 using CLI
Has anyone Created statoc route on the FTD sensor via the CLI?Mine looks like it goes throught bu when i FDM into it, i do not see them. Any Advice will be appreciated.Thanks.
redundancy in core layer
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
Resolved! I want to advertise only specific OSPF routes.
The route learned by OSPF from the LAN is re-distributed to OMP for publicity to other sites.I do not want to advertise the specific routes from OSPF. What kind of 'configuration' should we use ?I want to control this in the SD-WAN Router side, not t...
Setting a GRE tunnels between a NAT to a public IP.
Hi everyone.. i have been looking through multiple posts on the forum for similar cases but have not found the answer Im looking for.. I've been primarily using this thread for guidance. https://community.cisco.com/t5/networking-knowledge-base/settin...
cisco lock
hey.i need to know how can i lock my username for a time more than a month from my access not managerial access?
L2VPN Over GRE
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
Resolved! New Blog: Announcing the Launch of Webex Web Meetings SDK v3
New Blog: Announcing the Launch of Webex Web Meetings SDK v3. In this blog post, the Webex Developer Platform - Web Team announces the launch of the Webex Meetings V3 SDK, along with its features. The post also includes a link to a webinar where the ...
Resolved! New Blog: Changes to the Meetings Server API and SDKs
New Blog: Changes to the Meetings Server API and SDKS, as they relate to the Webex Suite Meeting Platform. Join Raffaele Lagana for an overview of the steps required to migrate your current Webex SDKs workflows to the new Webex Meeting Suite Platform...
ASR1001-X Thruput only 750 meg Interfaces10G both sides -Circuit 10G
We have a Cisco ASR1001-X and it can only pass 750 megs of traffic thru it on a 10 Gig circuit. I looked at licensing levels and they seem correct. Anyone have any ideas of what I can look at? Both Lan and Wan interfaces are 10 gig and Wan is using S...
