Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
LoadBalancing on viosl2
by geppone -
[注意喚起]ISE 3.2でのconfiguration backupのrestoreに関して その2
by maarai -
[UCS] 互換性確認ツールの使用方法
by yusnakan -
NAD config for 802.1x/MAB with ISE
by babalao -
CDP Mismatch from CDP: Why?
by Chris Schroeder -
Multiple sub interfaces with Native vlan's?
by jroy777 -
Ask Me Anything - Drive to 15X
by Brooke Hammer -
2960-CG IGMPv3 Snooping minimal
by pit-maravich
Community Activity
Cisco ISR not getting DHCP / IP Address
My router not getting IP Address after reload. Interface IP-Address OK? Method Status ProtocolGigabitEthernet0/0/0 192.168.231.9 YES NVRAM up up---GigabitEthernet0/0/1 unassigned YES DHCP up up--- Gig 0/0/1 Connected to ISP Router, since we not gett...
Forward traffic from subnet to another on C3750
hi guys thanks for your suggestions in advancei just reconsidered my whole message. after trying some things. i think i need to set up acl but i'm far from good at it.what would be the ip access-list extended or access-list lines that'd allow me to h...
Where is the FTD/Anyconnect/Cisco secure client Compatibility matrix?
Hope you guys can help. I need to know if Anyconnect 4.10 is compatible with FTD versions 7.3 & 7.4? I am aware Anyconnect is no longer under support (as of 31/03/2024), We're in the process of upgrading our ASAs to FTDs and we need to know if we...
WLC 9800-CL - help with correct interface/SVI configuration
Hello all, we are currently transitioning to a virtual 9800-CL WLC, hosted on a VMWare node on premise. The WLC and the FlexConnect APs are working correctly but I am experiencing a weird behavior with the interfaces. The APs are on VLAN 1 - 192.168...
After changing PPPOE max session , IPTV not connecting automatically A
Team,On this Te0/0/0.667 subinterface we have more than 200 users. so we set the PPPOE maximum session.After setting up PPPOE maximum session to 1000 , IPTV not connecting automatically and getting option SKIP or RETRY. after select skip IPTV getting...
Unable to Access Web Server - Whats Wrong with this Configuration
ASA working in IPSec, I am able to access HQ from UNIT No problem. Internet is only allowed on specific IPs which are outside DHCP Scope. When I assign IP for internet, now Internet is working, HQ Network is accessible, but S_EXT (webserver - 10.10.1...
[CISCO ISE][12935 ] Supplicant stopped responding to ISE during EAP-TL
Hello Everyone, I am contacting you all because i don't seem to find the needed information to resolve my issues, even though there are many similar topic as mine with the same error.We have an infrastructure using FTD ASA5506 with switch CISCO WS-C2...
ISR 4k Netflow not sending data
I've got 15+ Cisco ISR 4000's (a mix of 4331s and 4551s) in our network and when trying to setup Netflow to PRTG, It seems that when I hit 5 interfaces that need to be monitored, there is always 1 that won't come up in PRTG and that doesn't send data...
API call to get agent status
Hi, i am trying to get the Finesse agent status from asp.net using javascript but all i get is server responded with a status of 415 (Unsupported Media Type).what i got so far var agentID = "user"; var finesseEndpoint = "http://mydomain.com:8082/fine...
NTP and Syslog packets with specific IP Address
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Web Application Server
Dear Community,I'm asking for you guidance. I have come across a challenge on Cisco ASA version 9.8. Need to allow a web server to be access outside(Public) from DMZ Zone to Ouside Zone. Per below configuration template. Nat is transilating but acce...
MST convergence takes 5 seconds
Hi,I have been testing MST in my lab which has 3x Cisco Catalyst WS-C2960CG-8TC-L switches.I configured only MST and LACP on each switch and connected them in the ring topology. Test is to see how much time it takes for convergence in such conditions...
Macro auto execute does not work (Autosmartport macro)
Hello,Pleased help me! I have configured macro auto execute on Switch C3560E as below but it does not work, The idea is that when a link change to up, the switch automatically assigns this link to VLAN 10, and then link down, switch removes this link...
Cisco UCCX - Controlling Ready/Not Ready on Specific CSQs
Dears, One of our customers has requested a custom gadget inside Finesse where agents who have more than 1 CSQ can choose which one to be ready on; the current state is the agent has to choose to be ready or no ready on all CSQs. Any hints? Thanks in...
Resolved! Please help us investigate Service "ipfib" (PID 12792)
We found N7K-C7010 line card module 3 reload and found logging as below. 2024 Apr 26 13:08:19 SNIPER-01 %SYSMGR-SLOT3-2-SERVICE_CRASHED: Service "nfp" (PID 1130) hasn't caught signal 11 (core will be saved).2024 Apr 26 13:08:20 SNIPER-01 %NFP-SLOT3...
