The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello Community,I am looking a script for switches cisco for block interfaces with APs connected , the reason is because we receive daily port changes and sometimes the engineers change the vlan Wi-Fi by another and the Wi-Fi environment is affected ...
Our Customer is facing issue on their corporate SSID , We have capture debug and found below logs . Can anyone suggest what can be issue , currently WLC is on IOS 8.5.171.0 and access points connected AIR-CAP3702I-Z-K9.Debug logs apfMsConnTask_3: Apr...
I can't seem to overcome the following error when configuring AnyConnect with SAML according to https://community.cisco.com/t5/security-knowledge-base/configure-anyconnect-with-saml-authentication-on-ftd-managed-via/ta-p/4467779:Deployment Failed: Us...
Can anybody tell me what exactly is the difference between the radio MAC address vs the ethernet and Wi-Fi mac addresses? What is the purpose of the radio MAC address? Apparently, wireless access points don't just have an ethernet and Wi-Fi MAC, but ...
Hi,on ISE 2.4 in the live logs pages the report that one got clicking on the repeat counter was very useful because the endpoints were sorted by repeat counters. So it was very easy to find the endpoints with high repeated counters.With ISE 3.2 the r...
Hello, We have observed both on HP and Dell laptops and workstations that if they are using Intel I219-LM NIC they intermittently do not respond to EAP Identity-Request. We have excluded and have confirmed with Cisco and Microsoft TAC any other poten...
Scenario,Host-A(10.10.30.3/24) connects to access port on SwitchA with various other vlans also configured via access ports. SwitchA connects on a Trunk port to a CatSwitch. Firepower inside ½ interface trunks to CatSwitch. On The CatSwitch 3 vlans; ...
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
Is it possible to mark a variable as optional in sd-wan cli template?Can we use variables in a local data policy? I want to apply an ACL to internet facing interface that only permits traffic to the internet facing IP only. Policy will be applied to ...
I'm having problems setting up my home network using Cisco2921 for the first time. It has the basic licenses only. Below is the running config followed by my adapter settings. Any assistance would be greatly appreciated. Thank you.Current configurati...
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
When a client connect to the HQ via AnyConnect vpn, they can access the HQ local subnet, but can´t access the subnet at the remote office, that has an site-to-site connection to the HQ.Can this be configuret via the Cisco Firepower gui?Cisco Firepowe...
Hi,I have been curious about CCIE certifications. Does anyone know how many Cisco Certified Internetwork Experts are there and also who has the #1 CCIE certificate?
If my ISP is logically routing between a routed interface on their end with an IP in the same subnet as my end's Layer 3 router SVI interface for VLAN 10, but the ckt terminates on a layer 2 switched interface on my end using vlan 10, does my ISP nee...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: