The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Wednesday, April 10, 2024 through Wednesday, April 24, 2024. Our Community VIPs, Kathy New and Maren Mahoney will be waiting to assist you ...
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
I'm in the process of updating all our FTD's from Snort2 to Snort3 & almost everything appears to work, except SMTP/S email.Under Snort2 it shows in event logs as SMTP/S Client traffic type correctly, but when Snort3 is enabled, it does not recognise...
We are trying to accommodate an employee with hearing impairment so that they can use a TTY Display AND there is a compliance need for call recording. Has anyone been able to overcome this obstacle? We are running up against the inability for Call ...
I'm a newbie but have a question: I upgraded my Palo (firewall ) and the port that the firewall is plugged into err-disables out. After doing a SHUT, NO SHUT the port came back to life. Any thoughts on why this happens? It seems to happen anytime I u...
Hellocould you please share the solution for showing dropped packet from internet to inside lan ? i have FTD 4100 series managed by fmc I want to see output from cli or fmc related to nat transactions packet(dropped and passed) both.
NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...
i cannot log in to the SNTC portal, i have the necessary roles that were applied last week (beyond the 24 hour period that is required for SNTC portal access), but each time i try to log in at services.cisco.com, I'm redirected back to the registrati...
Hi,FTD was added and to FMC and while configuring HA in FMC, deleted FTD from FMC.While trying to add again to same FMC, both primary and secondary FTD not getting registered in FMC.Could you please help on getting the FTD registered with FMC.
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
We have clients receiving a "PKCS12 (PFX) without a supplied password" error while connecting to RAVPN using Cisco Secure Client (5.1.2.42). The headend device is FTD 3130.The full error is "There was an erro during initialization: PKCS12 (PFX) witho...
Please see attached pic. In this question, the destination address 10.0.1.15 matches the route in the routing table. But it's the broadcast address within that range. Would the packet still be routed with that route?what would the next hop be? 192.16...
We are noticing that devices that are no longer on the network eventually drop out of the collector. No issues there but we are wondering what the time period is and if it can be changed for how long a device stays in the collector once it is no lon...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: