The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Deployed a 3100 in chassis mode to the FMC a few days ago. All went to plan.Determined we needed to change the IP so decided just to delete the device from FMC and re-provision it.On the FTD via local-mgmt did a erase configuration. The device wiped ...
Hi Everyone,Cisco ISE 3.2 keeps crashing several days after the installation.The installation has been done successfully without any problems.After a couple of days the installation is malfunctioning.After several installations and change of the sel...
We are having an issue were after disconnecting from AnyConnect and connecting the next day, they get a new IP in AnyConnect but in our local DNS they have another IP which I assume is probably from the day before. This obviously causing name resolut...
Hi all.I am attempting to add an access group to a switch port which is located in a C1111 ISR router but the command is no longer there when using version c1100-universalk9.17.06.03a.SPA.binMy-Router(config-if)#ip a?admission arp auth-proxy*******...
Ask Me Anything Forum - Drive to 15X Welcome to the Cisco Support Community Ask Me Anything discussion! Are you considering upgrading or migrating your UC applications to version 15.x, such as CUCM, CUC, IM&P? If you're looking to learn more about...
Hi all,I installed application policy so I could configure QOS within DNAC. All was complete and the app policy section was showing but after leaving for an hour and coming back to it I can no longer see it as an option and cannot amend my config..Wh...
I've migrated one pair of 9800-80 from 17.9.4a to 17.12.3. I noticed that the APs w/ RRM on the new 17.12.3 on 6GHz have drop drastically up to 8 dBm (see attched picture). Is anyone aware of this change and why on 17.12.3?
I've a live instants where I've setup a monitor session on a stacked pair of C9200 running 17.09. CAT9K_LITE_IOSXE. Monitor session passed through another stack of 2* C9300-48UXM and 2*C9300-12 also on 17.09 CAT9K_LITE_IOSXE.Then into a VM host where...
We have 2 SG350x-48 switches in a stack. and we need to add another switch. but I know that SG350x-48 is no longer sold. what are my options? these were replaced by the "Cisco Business 350 Series Managed Switches". can one of these switches be a...
Hi,We have mGRE DMVPN tunnle between one Hub and 7 Spokes. Other 6 Spokes are working fine but one Spoke is not connecting to Hub.Spoke shows DMVPN on IKE state (tunnle is not working) and Hub is not adding nhrp entry in table.Spoke DMVPN TunnelPleas...
I own a CBS350-8XT that is far too noisy. I even purchased a sound meter to obtain a measure and it goes up to 70db where the maximum indicated in the user manual is 41.3db. I would like to open a ticket or something for cisco to fix my unit. How sha...
I just wanted to clean up * decommissioned and * physically removed blade servers by * selecting one and pressing ["Delete"] at the bottom as usual from the inventory. But UCSM fails: "Operation is not permitted" Any Idea how to overcome this?
Hi,I am trying to set up an SSH connection to my switch, but right now there is some lower level problem. I have set up my FastEthernet0 interface to ip address dhcp and the command show interfaces FastEthernet0 shows the correct address. Even if I t...