Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1937646members
1264455discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Image upgrade failed - rommon now

Hi all-I have an old 6509 with a SUP720 that I seem to have killed. I was trying to upgrade the code.Before the reboot, she file systems looked like this:and the sup-bootdisk: directory looked like this:I changed the boot line in the config from    b...

WesSchochet_0-1715278886341.png WesSchochet_1-1715278954084.png WesSchochet_2-1715279082033.png

DNA Center Per site override

Hi,When overriding certain wifi settings for a particular site in DNA Center, these changes creates a unique profile that is pushed to the wlc.How would i inherit back the global settings for this site? 

Kenny69 by • Level 1
  • 256 Views
  • 3 replies
  • 0 Helpful votes

ISE : Bug Trend(2024年 3-4月)

はじめに 本記事では、Identity Services Engine(ISE)をご利用いただいているお客様環境で発生した不具合のうち、1ヶ月間のTop 5を紹介させていただきます。ワールドワイドにおいてTACにService Request(SR)での報告数をベースとしています。本記事作成時点(2024/5/14)の情報のため、修正バージョンなど変更が発生している可能性があります。各不具合の最新情報についてはISEのリリースノートや各不具合情報をご確認ください。特にシビラリティが高い不具合に該...

Yuji Suzuki by • Cisco Employee
  • 23 Views
  • 0 replies
  • 0 Helpful votes

VTP and HSRP config on two core switches

hello Experts,Please help me regarding VTP Server config on 3560E.I have configure multiple vlans on both the core swithces below is the example, my question is how will be my VTP server configuration on the 3560E since both the core switches will ha...

C1111-8P VIPTELA Out of Sync

  Hello, I have several boxes configured, but one in specific does not synchronize with the information entered in viptela, when trying to change it to controller mode I have this error log, I have already invalidated its certificate and deleted it, ...

Use two vpc peer-link in Cisco N9K

hi,is it possible to configure two vpc peer-link (port-channel trunk) between two N9K?i.e. port-channel 1 would be a temporary trunk and uses MM fiber cable and port-channel 2 would be the 40GBASE-CR4 pre-fab direct cable.the 40GBASE-CR4 would arrive...

DAI conflict with inter-VLAN routing

Hey community, I have a 3-tier architecture, with 4 VLANs 10-40, I configured inter-VLAN routing on distribution switches and it's working fine, however when I pursued to configure DAI on access and distribution switches inter-VLAN routing is not wor...

raoufesi by • Level 1
  • 82 Views
  • 1 replies
  • 0 Helpful votes

%Port 500 is being used by system

Hey!I'm trying to add a NAT rule to my ISR 4321 (Cisco IOS XE Software, Version 17.03.05) for an IPSec VPN running on an ASA 5515-X, but I am receiving the following message. I'm not running IPSec on the ISR as far as I'm aware. Any ideas? isr4321(co...

joshdouch by • Level 1
  • 96 Views
  • 2 replies
  • 1 Helpful votes

Egress vs Ingress PCC

Hello everyone,  Could anyone explain me, please, about the difference between Egress and Ingress PCC. While reading RFC about the PCEP protocol can't catch the real meaning of these two terminologies.  Thank you in advance!

dundient by • Level 1
  • 66 Views
  • 0 replies
  • 0 Helpful votes

Flex Anyconnect vpn and site to site VPN

Hello all, I need your help to come up with a solution.A user is connected remotely to host location via flex Anyconnect remote vpn(vpn pool - 172.17.1.1 to 172.17.1.40). And also, there is a site to site VPN between the host location(192.168.1.0/24)...

MriduD by • Level 1
  • 58 Views
  • 1 replies
  • 0 Helpful votes

Routes behind a tunnel-te unlabelled

I have created a tunnel-te from xrv16 to csr3, the tunnel is up and getting Pop label to csr3 that's ok.From xrv16 I have learned the route to xrv17 over the tunnel, but checking the Label it's unlabbled as well.I believe the route from xrv16 to xrv1...

Load more