The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello all,I'm trying to make sure I understand the procedure for refreshing our current L2 APIC's with our new L4 APIC's.Currently our fabric is running 5.2(4) , and the new L4 APIC's require either 5.3 or 6.0.5 (which has just come out and is what w...
Hi! Can you help me with troubleshoot, I don't know where I am wrong?I don't see on BUH2, route from BUH1 (81.1.210.0/24).I attached config from BUH1, BUH02, ClinicaA01, ClinicaB02, P0.
I have no experience with this hardware and i can't get it to work. Booting an image lands me in rommon with the error message:Baseboard and rommon type mismatch. Rommon upgrade needed.%Software-forced reloadI switched over the MSFC4 to a RSP720-3C-1...
Hello,are there any best practices on the authentication timer settings?Is it common to let the settings for authentication timer reauthenticate and authentication timer restart on defaults?RegardsSebastian
I was just thinking about how in the early 2000's when I was just a wee little lad (like 18), I wonder a pallet full of Cisco AGS, MGS, IGS, and CGS routers for $1. It cost over $100 to ship it, but it was awesome. I tried using them to study, but ev...
Hello,I have a question about migrating a IPSec tunnel from between a Cisco C981F-k9 and a Cisco ASA firewall to a tunnel from the same Cisco C981F-k9 router to a Fortigate firewall. What is the 'best' way to migrate this tunnel?Currently I have conf...
I'm having a bit of a bother with my attempts to install and run Cisco Configuration Professional software. From the cisco support website, the install instructions indicate a link to download the software for CCP. -> http://www.cisco.com/en/US/doc...
Dears, i am not able to see all the acls with object groups on gui , however in cli i am able to see all acls applied. i have an issue with checking and modifying the acls on gui ( note that i upgraded the switch to the v17.9.4a ). Need assistance pl...
hi all,we have a topology without any redundant link. Every access switch is directly connected with the core switch, and it's a port-channel between access switch and the core. RSTP runs on switches by default, and we do not explicitly configure the...
I have two Firepowers in two remote offices and i have two ISPs in each office, i had configured vti ipsec vpn between two offices but they are working with static routes, can i configure dynamic routing protocols for failover vpn? I tried to configu...
HelloWe've successfully enabled the ISE Guest Portal on our WLC, and it works well with PCs until we apply explicit proxy settings. After configuring the proxy, the guest portal no longer appears; instead, the PC tries to access the proxy server, byp...
Am trying to create a new local account on a Nexus 3048 so I can SSH to it if my Radius server doesn't work. Normally, I log in with my AD account which the switch uses Radius for authentication with that. However, when I run the command to create ...
Hello community, i have a question, but can`t find answer on it. If we have one listener for inbound and outbound communication and this private IP has NAT to public IP. We don`t have communication to mail server on private IP. Is it a problem if ...
FMC: v7.3.0 (build 69)FTD 1120: v7.2.5ISE-PIC: 3.2.0.542, Patch 4We have a new integration between ISE-PIC and FMC that we are trying to use in policy. I can see some users are shown in the Unified Events, but many entries show as "Not Found". For on...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: