Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1928645members
1242346discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Catalyst3550:ACL設定のインバウンド/アウトバウンドの適用先について

L3スイッチのACL設定についての質問です。accecc-listコマンドで番号付きアクセスリストを作成し、（例：access-list 100 permit icmp 1.1.1.1 0.0.0.0 any echo）作成したVLAN(1.1.1.254/24)にアクセスリストを付けたいです。このとき、in/out を指定したいのですが、(ip access-group 100 in/out)このインバウンド/アウトバウンドというのは、何視点でのイン/アウトなのでしょうか？ポート→VLAN→L...

Yuukoide by • Level 1
  • 0 Views
  • 0 replies
  • 0 Helpful votes

Trustsec Network Authorization not Working

Hi All,I am newly building trustsec in my environment,trying to add one of the switch under trustsec. Have configured Trustsec settings and COA on the ISE for the switch and added the appropriate aaa commands , radius servers and cts commands.But sti...

BD Subnet advertised over L3out

Hello when a BD subnet is advertised over an OSPF L3out, i'm seeing tha subnet as E2 external route with metric 20 on the router connectd to BL (VPC link). Why the subnet is shown as external and not internal OSPF route? Why the metric is 20 ? Regard...

AirBorn by • Level 1
  • 1 Views
  • 0 replies
  • 0 Helpful votes

Mitel - DHCP Discovery

Hi, I have a Mitel 5312 phone plugged into a switchport configured for ISE but when it boots up it gets stuck on DHCP Discovery. If I put the port to authentication open then it goes through and boots up as normal.The logs all look ok but I can't see...

Help with extended access list

So I've been working on my project and I've implemented vlans nad also router stick.Now I want to block connections between vlans that are not same with extended access list but something does not work..Here are the commands that I've writtenip acces...

AP9115axi

Hi ,I am facing one issue. AP9115AXI (access point) acquired IP address from DHCP. Confirmed with ARP table on switch.But  the command sh cdp nei detail - doesn't show IP address of AP. AP not yet associated to WLC.Any suggestion?With Regards,Ravindr...

ACL configure

I want to create an ACL on Cisco to prevent one network from communicating with others except for the internet. Can you help?

cyberpea by • Level 1
  • 88 Views
  • 4 replies
  • 1 Helpful votes

Brute force attacks towards ASA

Hi! The last weeks it has been a big increase of brute force attempts from all over the world to our Cisco ASAs. We use two factors, so we're not to afraid that they will actually access any of our accounts, but the problem is that they manage to blo...

Sonflaa by • Level 1
  • 33 Views
  • 1 replies
  • 0 Helpful votes

C9800 WNCd

i've seen this item "Site Tags AP to WNCd distribution" in best practice of C9800 Design and Deploymentmy quiestion is how can i configure multiple WNCd and where is the location of settings in webui? 

Felix5 by • Level 1
  • 198 Views
  • 8 replies
  • 0 Helpful votes
Load more