Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1928396members
1241818discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Palo Alto to Firepower migration

Hey All,Anyone know of any tools to migrate config from Palo Alto to Firepower (or better yet, secure device manager)? Needing to migrate 5x physical appliances and 1x virtual rapidly.We need to migrate: DNS (DNS Proxy) DHCP NAT Security zones Interf...

jackiedr1 by • Level 1
  • 52 Views
  • 1 replies
  • 0 Helpful votes

AP issue

Hello we have a local 9120axi AP with a 9800LC WLC that seems to be losing connection. The AP is in flex connect, all config looks fine: AdvancedCountry CodeUS  Multiple CountriesUSStatistics Timer180CAPWAP MTU1485AP Link LatencyEnabledAP PMK Propaga...

C9800-80 in HA cannot install APSP6

Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question:  Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...

Switch: Prompt 3650

Hi all, I have a 3650 stuck in the switch prompt. I've tried to set the IP address using the below commands so that I can upload the IOS, but I am unable to. set IP_ADDR Set DEFAULT_ROUTERbelow is the file system outputswitch: dirList of filesystems ...

Limit the number of concurrent logins to DNAC

Hello all, We have ISE with DNA Center merged. We have a requirement to limit/control the number of users that are allowed to login to DNAC at anyone time. Most Cisco devices can control this but is there a way to do this via ISE RADIUS/TACACS+? I ca...

Resolved! Nexus ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet is down

Hello,I have a Nexus 9K trunked to a C9200LOn the Nexus 9K the port is:interface Ethernet1/19switchportswitchport mode trunkswitchport trunk native vlan 888switchport trunk allowed vlan 1,254,995no shutdownOn the C9200L the port is:interface TenGigab...

open24hrs by • Level 1
  • 2304 Views
  • 3 replies
  • 0 Helpful votes

9800 WLC-Same Vlans on multiple sites in SD-WAN setup

I have a 9800-CL in an SD-WAN setup. I have multiple sites that have the same Vlans at each site to make it easier to manage and remember.Ex:NorthSite: data-4, voice-5, wifi-6SouthSite: data-4, voice-5, wifi-6etc...My current WLC configuration has on...

GeorgeC71 by • Level 1
  • 44 Views
  • 0 replies
  • 0 Helpful votes

separate wireless traffic from LAN traffic

I have some branch locations with a simple set up. A router with an access switch connected to it, then another access switch connected to that one to provide POE to IP phones. Currently all devices are in the same VLAN.I also have an access point co...

Help with extended access list

So I've been working on my project and I've implemented vlans nad also router stick.Now I want to block connections between vlans that are not same with extended access list but something does not work..Here are the commands that I've writtenip acces...

Load more
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: