The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
How do I speak to someone at Air France?Air France dedicated customer care team is always ready to assist you. Call +1@(804)-886-0886or +1@(804)-886-0886or ퟏ ퟖ04-푨풆풓풐풎풆풙풊풄풐 (24/7 Help) to talk to a live person at Air France customer service represent...
How Can I Speak to a 퐋퐮퐟퐭퐡퐚퐧퐬퐚 Representative Fast? {{헗헶헿헲헰혁 헟헶헻헲 헧헼 헦혂헽헽헼헿혁}}To talk to a 퐋퐮퐟퐭퐡퐚퐧퐬퐚 헔헶헿헹헶헻헲 live representative in a quick time, you can initiate a request in several ways. You can call their dedicated customer service line at “ ퟏ...
Hello,I have a question about migrating a IPSec tunnel from between a Cisco C981F-k9 and a Cisco ASA firewall to a tunnel from the same Cisco C981F-k9 router to a Fortigate firewall. What is the 'best' way to migrate this tunnel?Currently I have conf...
Dear community I am getting into NetFlow a little bit deeper but cannot get my head around sampling. All i understand so far: We can configure deterministic sampling, that uses a hardware sampler per interface, limiting the maximum number of monitori...
Hi,Per the title, I've got an issue with 5Ghz clients that have good signal strength because they are sat almost underneath the AP (1832 APs) yet but struggling to get more than 1Mbps throughput. I can see the channel utilisation is over 50% but zer...
The Cisco Document Team has posted an article. This document describes how to allow specific YouTube channels/videos and block the rest of YouTube in Web Security Appliance (WSA). Know of something that needs documenting? Share...
I have a C1111-4P router with c1100-universalk9.17.06.01a.SPA.bin image loaded, I want to update to c1100 universalk9.17.13.01a.SPA.So can I update directly to a new image or need to update any intermediate?
I am trying to configure a trunk port on a Cisco 3750 that has fiber running to a ruckus 7150 switch.My current config connects the switches but it is only passing vlan1 traffic and I want multiple vlans. Therefore, I configured the port as a trunk o...
Hi. After AnyConnect upgrade from 4.10MR2 to 4.10MR7 (pre-deploy) it downloads ISE compliance module 4.3.2403.6145 from ISE upon every connect and tries to install it, although 4.3.2403.6145 module already installed.I know there is a workaround to co...
Greeting everyone! There is a little problem with configuring tacacs server on ws-2950-24 model switch. The rest switches we have are 2960 series, also 3xxx series and others, more modern versions. We always configured tacacs server this way:tacacs-s...
Hi,I wonder if there is a way to send every incoming and outgoing message both to the original destination and to another destination for analyses. Preferably before any scanning or policies interfere.I've tried google, but have not come up with anyt...
Hello, I have two ISE 3595 (3.2 Patch 3) physical appliances, one in each Data Centre. They will be end-of-life in a few months. They are currently used for Wired NAC with Posturing, Wireless NAC (corporate, BYOD and Guest and Hotspot). It is also us...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: