The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
1. It's possible to launch into multimode using LRM optics as we have in our Cisco 6500's ?2. what is needed , possibly special launch cable , also what is needed on the HPE J9851A Switch 5412Rzl2 if going to a normal sfp+?
Dear Gents, What are the recommendations that should be followed if we have a local site with wireless APs operating in Local Mode and registering on a local Primary WLC on the same network. and in the case of Primary WLC failure, the APs w...
I have a Cisco 3700 Series AP and trying to connect it to a WLC 5508. I have getting a certificate validation failed error, however when I use the command "show crypto pki certificates" no such expired certificate shows up. Previously had an issue wi...
Hi,I have a core switch(4506e) connected to 6 edge switches(2960)..Each switch is configured with crypto pki trustpoint TP-self-signed WHat is this exactly and whats its use? Also, when i connect other 2960 with core, it automatically takes this cryp...
I am trying to figure out how to add an ap into a an existing EWC network currently have one ap c9130ax and I am trying to add another c9130ax both same country code, the new Ap has been reset and I believe it is in Capwap mode, currently I am unbale...
how do i remove a switch from the stack and return it to standalone config ? current configswitch 2 provision c9300-48uxm i tried Switch(config)#no switch 2 provision ?<cr> <cr>Switch(config)#no switch 2 provisionError: A switch is already physically...
Hi community,Few months ago I bought 3 POE AP CBW150AX for my house. And I have issues with two of them.I plugged two on my SG300 and everything seem goes well at this time.But one day, the switch port where one of the AP was plugged shut off. No mor...
Hi, Tech geeks. I have C9124AXE-E wireless AP and i have upgraded it to EWC by installing 17.9.5 version. now i have connected 4 external antennas with this AP / EWC. what i am facing is unable to get my 5ghz ssid operational, its operational status ...
Hi everyone, I want to upload the startup-config to real router via tftpd64 in vmware windows server. Windows server and ESR6300 are under the same network. But ESR6300 can ping windows server only from mgmt vrf. Through global router ESR6300 can'...
HelloAfter I have setted every policy on the switch and everything is working fine through an ISE authentification via dot1x, now server cannot reach its gateway in order to give IP DHCP addresses to the hosts on VLANs!Can anyone help me please
If you look at the tacacs profile as shown in the picture, there are custom characteristics I wonder how this works. In the case of other banders, I understand that tacacs are linked using these attributes If you add a value here, compare it with the...
Hello Bro, I have an issue when I am trying to support my personel laptops, they have limited access to the windows "users not admins" and whatever I set the UAC window setting, I am still unable to enter the admin password in UAC popup wi...
I'm just automating my company's network using Ansible and Netbox for dynamic inventory and Source of Truth (SoT). I have a general question: how do you deal with old, unsupported IOS devices when working with Ansible? Some modules require commands l...
I have one device southbound locked and one active device. One service is managing those two devices.When I send PATCH request to "/restconf/data/?commit-queue=async" , commits are queued for locked devices, this is fine.However, commits are not queu...