Cisco Community

Redundancy Over VSAT Link

Hi, we have a WAN and VSAT connection to one of the site. WAN is primary and VSAT is secondary link.We have dedicated router for WAN and VSAT. VSAT link is connected to one of the LAN access switch.Could you please help me, what kind of configuration...

Simple nat config refuses to work on Cisco ASR 1001 ???

I have simple nat config which I need to use:ip nat pool test 40.0.0.3 40.0.0.3 netmask 255.255.255.0ip nat inside source list 1 interface GigabitEthernet0/0/1 overloadip nat inside source list 2 pool test overloadaccess-list 1 permit 10.0.0.0 0.0.25...

Configure Port-channel and vPC in advance in Nexus 9K

hi,i'll be configuring a new N9K switch to replace a C9300.my question is, can i configure in advance the port-channel and vPC in the N9K even without the SFP inserted and fiber cables patched?just want to prepare the config so it will be a faster to...

Cisco ISE integration with SCCM

Hi While Integrating ISE with SCCM 2012 based on below link, i am getting error related to DCOMhttps://community.cisco.com/t5/security-knowledge-base/how-to-integrate-cisco-ise-with-microsoft-sccm-for-patch/ta-p/3725035 Do any one having solution on ...

The operation took longer than expected.

I have just synchronized both Active Directory and Cisco ISE, ISE is using my server (AD) as an NTP server, everything is fine, but now I'm facing an issue "Status Summary: The operation took longer than expected. This may be caused by slow network c...

CBS350 IGMP and filtering unregistered multicast

Hi.We have issues with CBS350 and SG350 switches when it comes to deal with multicast in the following ranges:Local Network Control Block (224.0.0.0 - 224.0.0.255 (224.0.0/24))Internetwork Control Block (224.0.1.0 - 224.0.1.255 (224.0.1/24)) We use t...

user auth without user cert?

We have a chicken & egg situation where ISE requires a user's login and the presence of a user cert from AD before the user can be permitted to connect to the corporate wifi. But the user needs to connect to wifi to get the cert. One solution i have ...

Site-to-site vpn failover causing memory spike in spoke sites

Hi All. I would like to get your thoughts on the following issue i have been facing since implementing Dual ISP and failover for site-to-site vpn tunnels.Hub Site:ASA5515 using 9.6(4)42Spoke sites:Cisco ISRs using 15.1(4)M8, using voip services over ...

Issue with Assigning a Provided Contract to vzANY in Cisco ACI

Hello everyone,I'm reaching out to the Cisco community for assistance with a problem I'm encountering regarding the assignment of a Provided Contract to vzANY in Cisco ACI. I've tried various solutions but so far haven't been able to resolve this iss...

Change icon on Room Navigator

I am looking to change the icon of the Room navigator to something else rather than the generic icon.I would like to change the green icon to my own logo or some sort.

Keep Up Interface to a device even when peer-link goes down on Nexus

Hello,i have a pc connected to VPC Peer Switch (vPC2) which has the secondary role. vPC2 builts a vPC with vPC1. How can i configure the port to always keep up the connection for this device, even when peer-link goes down (dragging out the cables).In...

NDFC: Switch を NDFC Fabric に追加しなおす手順

はじめにトポロジー手順1. 該当スイッチを Fabric に Add2. L3 に接続している S1、S2 側のポートを no shutdown3. Push Config/Recalculate and Deploy4. Recalculate and Deployまとめ参考資料はじめにこの記事では、NDFC (Nexus Dashboard Fabric Controller) の Fabric から削除されたスイッチを、再度 Fabric に追加しなおす場合の手順を紹介します。な...

Help with routing vlans

Can someone tell me how do I do routing here ? it does not matter if it is static or dynamic I just want to ping same vlans and also I dont want to have different vlans to be pinged

CSCwj75561 - Prox crashing/coring while matching HTTP Rewrite Profiles

Are these bugs affecting only for SWA hardware appliance ?or both hardware and virtual WSA are affected with these bugs?

Interface Vlan administrativamente inativa

Acabei de criar uma vlan, atribuí-la a uma porta em nosso 6509, atribuí à vlan um endereço IP e quando eu disparo o comando, show int vlan 31 ele diz que a vlan está administrativamente inativa. Não consigo descobrir o que está acontecendo aqui? emit...

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

Empowering Sustainability with Cisco and adidas

Community Activity