The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hey community, I have a 3-tier architecture, with 4 VLANs 10-40, I configured inter-VLAN routing on distribution switches and it's working fine, however when I pursued to configure DAI on access and distribution switches inter-VLAN routing is not wor...
Hi there,Will it sacrifice its wireless performance if an AP runs ME firmware instead of the lightweight CAPWAP stuff within an ME cluster (the controller is another AP)? I.e. I got 4x 3802I, is it better to convert 2, or 3 of them to be CAPWAP mode?...
Greetings, We had deployed mobility express for wireless complrising of 2800 1800, 1542 6300. But now we have to replace one faulty 1542 and as this is end of sale - catalyst 1542 is the optio Can 9124ax join existing mobility express or shou...
Hi, we have cisco 4431 router, but not sure need to purchase security license or not as we want to setup ipsec vpn on this router. Below is the output of the command "show license all". Is it indicating the security license is active and no need to b...
hi , we have only one Cisco layer3 switch (C3850) in our office ,and want to enable multicast routing between two vlan 2 & 3. How should configure pim on C3850? can use spare-mode or dense-spare-mode? Can anyone pls advise? thanks in advance!
Hello,We were impacted by the vulnerability https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asaftd-persist-rce-FLsNXF4h, and following recommendations from the TAC, I had to update my pair of ASAs from version 9...
Hello everyone,We would like to use our “old” C2960X devices, which we have in large numbers, to connect simple devices such as printers or PCs that do not require PoE. The goal is to use SGT for these devices. I have already read that it is not poss...
Set person being visited from a pull-down list of usersSet person being visited from a list of department and usersStatically Assign an Email Address for the Sponsor This document shows you how to enable your guests to choose from a list of sponsor...
I am using the latest version of packet tracer but still getting compatible issue and I can't find anywhere any solution of it anywhere if anyone knows how to open this file please help !! I am also dropping the file please if any know how to open, t...
Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1/1/2Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1...
Hi All,Thank you for taking the time to look at this post. I've got a bit of a situation where as I am tasked with Migrating all of our AP's (3802i) site-by-site from a pair of Physical WLC's at the Datacenter to a Pair of Virtual WLCs in the Cloud....
howdy, installing denali 16.2.1 on a 3850 stack, all similar switches. i keep getting this error when i attempt to install the package FAILED: Switch switch 4 boot path does not match with the active please advise.
Hello all,I have a small ACI deployment with only 2 Leafs. What I want is to have "Isolated" subnets that are behind a firewall connected to my ACI (so traffic to those "Isolated" subnets has to pass through that firewall).To accomplish this, say I h...
I need to know if the rule I configured and validated is a good configuration practice in a production environment, can you check and help me feel more at ease?I set up a laboratory to connect via PEAP EAP-TLS, it worked in the lab, but I would like ...