Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1928790members
1242598discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

ip nat command missing from 17.9.5?

Just upgraded to 17.9.5 on our 9800 WLC. Seems this statement is missing now... need a bug alert on this? Anyone can chime in. Was there on 17.9.3, unsure on 17.9.4. I do not see any information under the release documentation. We do not have support...

Dual ISP connection gi0/2 not able to connect to internet

Hello,I need your help - currently we have a  2921 Cisco router connected to dual ISPs using "gi0/0 & gi0/1" and we are able to connect to either ISP successfully.  Once we connect gi0/2 to any device the connected switch is not able to access the in...

dgrant524 by • Level 1
  • 56 Views
  • 6 replies
  • 0 Helpful votes

unknown IPs in FTD outbound logs

I am managing FTD-1120s with FMCv both running v7.2.1 software.  In my ACP I have a GEO rule to block all outbound traffic to China, Russia, and I few other "hotspots".   When I search for events that match this rule, most of the traffic is from inte...

tato386 by • Level 6
  • 141 Views
  • 3 replies
  • 1 Helpful votes

Resolved! SVI and Subinterface Ingress/Egress Unicast Counters

Hi,We migrated from Catalyst 6500 to Nexus 93180YC-FX3 core switches in vPC configuration running NXOS 10.2.4. What I miss in the SNMP monitoring are the traffic counters for the VLAN interfaces. I found the following in the Nexus 9000 configuration ...

Resolved! Cisco Firepower 2130 - no console access

I have a couple of Cisco Firepowers that I can access thru SSH or the FDM, but I can't console to them?-Software version: 7.0.5-72-Configured with primary and secondary-Base license-Not using FMCCan someone tell me how to get console access? Thank yo...

DSterling by • Level 1
  • 207 Views
  • 7 replies
  • 0 Helpful votes

IP routing using domain

The host for my current server (Windows Hyper-V machine with four or five VMs) that handles my email and web sites is going away. I'm planning on moving that physical server to my house and using DDNS to route that traffic in. Realize this is very lo...

The operation took longer than expected.

I have just synchronized both Active Directory and Cisco ISE, ISE is using my server (AD) as an NTP server, everything is fine, but now I'm facing an issue "Status Summary: The operation took longer than expected. This may be caused by slow network c...

Jason2005 by • Level 1
  • 22 Views
  • 0 replies
  • 0 Helpful votes

Supervisor engines configured for redundancy appear as "STANDBY HOT" and "STANDBY COLD" in the output of the show redundancy states command

Core issueRoute Processor Redundancy (RPR) refers to the provision of support for the redundancy feature. In the RPR mode, one of the supervisor engines is active and operational, while the second supervisor engine is in the standby mode. If the acti...

TCC_2 by • Level 10
  • 20587 Views
  • 1 replies
  • 0 Helpful votes
Load more