The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
I have a bench IE4000 switch which had previously been running on 15.2.4 EA(5) code. I was experimenting with disabling the SD card, but neglected to put the IOS image into the local flash of the switch before disabling this. Naturally it went into R...
Hi TeamNeed help with files uploaded to cisco ise repository. All settings related to FTP and file permission done but yet couldn't access files in the repository. See below error message: XP-ISE-02/admin(config)# repository ftp-repoXP-ISE-02/admin(c...
Dear Community,There have 2 kind different of AnyConnect agent version on ISE.Also have 2 kind of Complain Module as well.There are 2 kindly of Cisco AnyConnect agent on ISE where Client Provisioning Policy. 1. AnyConnect 4.x with its Compliance Modu...
I have configuration in which port which is connect to cisco AP is trunk port, but management VLAN is configured as native.I want to know what is rationale behind this?
we are using Cisco Aironet 1815i Access Point as a WLC and Access point and need to be upgrade the firmware version 8.5.140.0 to 8.10.185.0. please suggest the step by step process that we need to be followed.
Sad. I would expect you buy Cisco products from a authorized dealer, buy smartnet total care and then Not only will Cisco refuse to let me use my paid for contracts and not even allow attaching them to my account because I have a gmail.com address an...
Hello,We had a power loss on our site - equipped with 6 * Aironet 1830 Mobility express Series.The "master" Aironet lost power, so we had to reboot the whole 6 APs.The method is as follows :- first shut down the 5 "slave" APs- verify that the "master...
I need to upgrade vFMC to 7.2.5 version but at this moment i don't want to upgrade my FTD to new version , my FTDs are at version 7.2.4 , will FMC be ok managing lower version of FTD? Thanks
Dear Community, We use ISE 3.1 P6 we notice there are some anomalous behavior endpoints increase day by day. There are some endpoint not connected long time, some PCs hit Default policy, some PCs are status connecting including MAB profiling. Is ther...
Every time I press the pound key then any number after it the phone says invalid number without me putting in the full ext. #968 is my page code. / Overhead paging code. Is it the dial plan?
Hello all,Maybe this question was published before but i was unable to find an answer that solvedy issue.I acquired an UCS C240 M4 recently with firmware version 2.0.I upgraded to version 4.2 without problem.Since I had no access to the CIMP web int...
I have a home network setup. I am tearing down a lot of it as I don't use it. Parr of it is taking out the small rack my 48 port Cisco switch was in as I need the space. My question is, can I put my Cisco switch on a table top and let it sit there an...
I need to migrate some users off an old CUC cluster. COBRAS Export is giving me this error:(error) in DownloadWAVFile on ConnectionWAVFiles:The underlying connection was closed: An unexpected error occurred on a receive.Wireshark shows CUC sending a ...
On a Cisco 9300 I need to Downgrade Boot Loader (ROMMON) from 17.9.2r to 17.3.2r. As a test I upgraded to IOS from 17.3.4 to 17.9.4a, as expected the Boot Loader upgraded as well with the IOS upgrade. When I upgraded the the IOS I did not initiate th...