The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Talk to someone on 헔헹헮혀헸헮 헔헶헿헹헶헻헲 smoothly, give their dedicated support line a ring at +[ퟭ-ퟴퟬퟰ-ퟴퟴퟲ-ퟬퟴퟴퟲ]. Take your time and listen carefully to the automated prompts, then share all the required information to help them solve your problem quickly. ...
Hello we have a local 9120axi AP with a 9800LC WLC that seems to be losing connection. The AP is in flex connect, all config looks fine: AdvancedCountry CodeUS Multiple CountriesUSStatistics Timer180CAPWAP MTU1485AP Link LatencyEnabledAP PMK Propaga...
Talk to someone on 헔헹헮혀헸헮 헔헶헿헹헶헻헲 smoothly, give their dedicated support line a ring at +[ퟭ-ퟴퟬퟰ-ퟴퟴퟲ-ퟬퟴퟴퟲ]. Take your time and listen carefully to the automated prompts, then share all the required information to help them solve your problem quickly. ...
Bonjour a toutes et tous,je voudrais savoir comment se connecter via un PC sur l'interface d'administration d'un point d'accès CBX150AX.Merci d'avance pour vos reponsesJJ
Talk to someone on Hawaiian 헔헶헿헹헶헻헲 smoothly, give their dedicated support line a ring at +[ퟭ-ퟴퟬퟰ-ퟴퟴퟲ-ퟬퟴퟴퟲ]. Take your time and listen carefully to the automated prompts, then share all the required information to help them solve your problem quickly...
Hello friends, I have a virtual WLC 9800 running version 17.6.5. A client is unable to connect from a specific PC, but can connect successfully from other devices. I have verified the credentials, and they are correct. The specific PC can connect nor...
Talk to someone on Hawaiian 헔헶헿헹헶헻헲 smoothly, give their dedicated support line a ring at +[ퟭ-ퟴퟬퟰ-ퟴퟴퟲ-ퟬퟴퟴퟲ]. Take your time and listen carefully to the automated prompts, then share all the required information to help them solve your problem quickly...
I configured NAT and DHCP relay in GNS3, and all hosts have end-to-end reachability, I can ping PC44 from PC11 and PC22, and also from PC33 if I configure a static IP address.On the NAT router (R11), I also configured DHCP relay with 'helper-address'...
Hello everyone, I have the following issue:The customer would like to disable FMC packet fragmentation globally. According to the Cisco documentation it is quite straightforward.Source chapter: Fragment SettingsCisco Secure Firewall Management Center...
Dear all,I am configuring a network cfomposed of 4 VLANs with the following devices:- NetGate 6100 Firewall- A Cisco 2951 Router- Ciscon 2960 SwitchVLANs and DHCP were configured on the 2951 router.Note that NAT function is handled by the Firewall.Af...
A simple question....If I just knew where to find the answer:Doing MAC authentication on an 5520 WLC, I can see the MAC addresses accepted by the WLC if I issue the command:"sho macfilter summary"Can anyone tell me the equivalent command on a 9800 (y...
Hello,Studying for my CCNA and I thought I'd practice some basic configurations, such as router on a stick. I setup 4 PC's (each representing an imaginary number of hosts) each with a vlan attached to a switch leading to a router, with the link betwe...
Good morning friends,I have created two extended ACLs for in and out of my int vlan and applied it under int vlan for both directions inbound and outbound. I have created ACLs entries like this.For int vlan no. Out1 permit ip 10.1.0.0 0.0.255.255 hos...
hi i am trying to cable up trhe ucs 6454. I got 2 40G mopdules on port 53 and 54 on each fabric. I got 2 core switches to connect therm to FABRIC 1port 53 ----> port 1 on Core switch APort 54 -----> port 1 on Core Switch BFABRIC 2port 53 ------> port...