The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello Everyone, one of my clients currently have a CUCM cluster with 1 publisher and 6 subscribers, this cluster is running version 11.5.1 SU2. i am planning a refresh upgrade to version 14 using PCD. but before this upgrade, i am planning a minor up...
How Can I Speak to a 퓐merican 퓐irlines Representative Fast? 【American Guide 헙헮혀혁 & 헙혂헿헶헼혂혀】Talk to someone on American Airline smoothly, give their dedicated support line a ring at +1-[888]829~1316. Take your time and listen carefully to the automate...
I have a requirement to create an ikeV2 S2S with a client and client requires to use Asymentric PSK. However there is no option to configure Local/Remote PSK on the FTD. When i check the same on the CLI, it shows the config and suggests that both of...
Hello Team,Please help me to understand: in hybrid scenario of Controller deployment, if vBond resides behind the NAT, and lets say cEdge on-boarding is done with the Internet as TLOC then as we know, vBond should learn both the Private and NATed pub...
Hi Everyone,Cisco ISE 3.2 keeps crashing several days after the installation.The installation has been done successfully without any problems.After a couple of days the installation is malfunctioning.After several installations and change of the sel...
Hello Guys,Good Day !!Need your help and guidance on cli commands to configure the NAT for the Internet Link on cisco cEdge for the direct L3 TLOC extension (Private IP address) between the 2 cEdges.In vEdge we can simply config NAT enable under the ...
Hi,we have this fresh install of DNA Center 2.3.5.5-70026. I've been able to create areas using the Intent API but I can't create a building.sitePath = "/dna/intent/api/v1/site" headers = {'content-type': 'application/json'} headers["X-Auth-Token"] =...
I configured NAT and DHCP relay in GNS3, and all hosts have end-to-end reachability, I can ping PC44 from PC11 and PC22, and also from PC33 if I configure a static IP address.On the NAT router (R11), I also configured DHCP relay with 'helper-address'...
Our Forum Alert III Secondary Crash Net (SCN) is inoperable. I've heard the cisco cm could be configured to set up some devices to act as a ringdown, they called it a “Switch Box.” This would allow our Base Operations guys to have a work around from ...
Hello Guys,Good Day !!This is very strange that : on version 20.9.4 the login banner is coming after the login prompt but it is perfectly coming on version 19.2.31 i.e. before login prompt.Would you please help me to fix : i am on version 20.9.4Early...
Hi dears if i see advetise routes prefix to nieghbor X.X.X.X by details for example which community send wightand other bgp parameters How can see thisin bgp nexus switches for examples 9K series???
A simple question....If I just knew where to find the answer:Doing MAC authentication on an 5520 WLC, I can see the MAC addresses accepted by the WLC if I issue the command:"sho macfilter summary"Can anyone tell me the equivalent command on a 9800 (y...
Hi allI'm attempting to use 4 cisco SG350-28 switches connected around 100 meters apart. 3 switches will connect to 1 "central switch", each using a LAG (the far away switches are using SFP fiber modules). I have this setup and all seems to be workin...
This is the standard template we are using for AP connected interfaces.interface GigabitEthernet 1/0/8descriptionXXXXXspanning-tree portfastswitchportswitchport mode accessswitchport access vlan 90logging event link-statuslogging event power-inline-...