Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1920429members
1225470discussions

Community Activity

DHCP with Router on a Stick fails; instead uses APIPA.

Hello, I was working on a topology that incorporates inter-vlan routing as well as dhcp pools for each vlan. I got my inter-vlan routing to work with static addresses, and all devices can ping the default gateway currently. The router acting as the d...

8MFT-T1/E1

how to activate the module on cisco 4400 router for E1 connections.#card type e1 0 4 showing error, card not found or command wrong

DUO - RDP - LogonExpert

I have a number of servers that MUST run an application as the Administrator as soon as the machine restarts for any reason.I cannot run this application as a Service.To facilitate this, I use a tool called LogonExpert which logs in as the administra...

markbailey_0-1711853105787.png

IPSec tunnel encrypt packts but no decrypt

Hi Community, We have a newly established IKEV 1 tunnel from Cisco ASA to AWS. This tunnel is currently at up state but the traffic is not passing through the tunnel. When we enter the show command "show crypto ipsec sa peer X.X.X.X" output have enca...

naveen98 by Level 1
  • 422 Views
  • 12 replies
  • 0 Helpful votes

IOS-XE always on sandbox not working

Unable to establish reachability to always on IOS-XE always on environment.   MacBook-Pro:~ mike$ ping devnetsandboxiosxe.cisco.comPING devnetsandboxiosxe.cisco.com (131.226.217.181): 56 data bytesRequest timeout for icmp_seq 0Request timeout for icm...

mbrown294 by Level 1
  • 69 Views
  • 2 replies
  • 0 Helpful votes

SNMP ifmib ifindex values

I have an ISR4331/K9 reporting incorrect ifindex values.RTR-003-4331-01#show snmp mib ifmib ifindex Gi0/0/0Interface = GigabitEthernet0/0/0, Ifindex = 1RTR-003-4331-01#Clearly the index values is 1, however my Netflow tools is discovering this as ifi...

DUO MFA for ASA Admin/management

We have an old Cisco ASA (5508) which has Duo configured for AnyConnect VPN, but using local accounts ONLY for Admin/Management. We are moving to a new FirePower device (in ASA mode) and want to enable some sort of SSO or MFA for Administrators using...

jeff76 by Level 1
  • 69 Views
  • 4 replies
  • 0 Helpful votes

Cisco 562 Headset Turns Off Phone

I am try to use the 562 headset with the mult source base and when I hook up both the phone and computer, the phone turns off. I have model CP-7841 desk phone.  If one source is plugged up (either the phone or computer) there is no problem.  The prob...

wmargolen by Level 1
  • 593 Views
  • 4 replies
  • 1 Helpful votes

Cisco catalyst 8000 as a proxy server

Hi, Currently I need to  configure the proxy server address in browser lan settings. So it is very difficult for me to configure the same in new pcs ( I need to do it one by one in new machines). So is there any way to configure my catalyst 8000 swit...

saidcr7 by Level 1
  • 31 Views
  • 0 replies
  • 0 Helpful votes

Native VLAN mismatch detected on interface

Hello I have Cisco CBS350 switch connected to Cisco router C1128, just noticed the below error from the switch  %CDP-W-NATIVE_VLAN_MISMATCH: Native VLAN mismatch detected on interface gi1/0/1.I tried to run the command: "show cdp neighbors gi1/0/1 se...

mmarie by Level 1
  • 246 Views
  • 7 replies
  • 0 Helpful votes

Connecting two private 10.0.0.0/8 Networks

Hey there,I'm theocrafting about a network problem and I'm struggling with the following situation.company A uses 10.0.0.0/8 network for internal traffic.company B also uses 10.0.0.0/8 network for internal traffic.I need to connect these two company ...

Lisytiro by Level 1
  • 313 Views
  • 5 replies
  • 0 Helpful votes

Please help with this Topology Configuration

Configure Open Shortest Path First(OSPF) Update should be advertised only out of the interfaces that are indicated in the IGP topology diagram OSPF process ID is 47 Configure OSPF router ID with interface loopback 0 on respective router.What is the r...

Site 1-ospf connectivity.png

CX

Create CX Cloud App for IOS and Android in order user can manage asset from smartphone

bezeddin by Level 1
  • 260 Views
  • 2 replies
  • 1 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: