Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
How to Pass the DevNet Specialist - DevOps exam (300-910)
by Alex Stevenson -
CTF: my first post
by mmuench -
ACL configure
by cyberpea -
Help with Jabber contact list import
by sebastian-friedemann -
Should we enable allow-service netconf all the time?
by yutashimamura2920 -
Lock AnyConnect profile to specific certificate
by Crag Muer -
CML 2.7 NODE not working
by MAC2929 -
WLC 5508 licenses
by angel almaras
Community Activity
CSCwh18572 - Headless iPSK/mPSK
Why can't Cisco catch up and do this? It is such a simple concept. Aruba, Ruckus and even Ubiquiti can all do it. I don't mind running a Radius server but dot1x is not suitable for many environments. We have events where 5000 people turn up on first ...
Trunking an ip addressed inside interface on Firepower 2130
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
CBS350 Setup guidance
Hello,I have an ISP router/modem, along with assignable public IP addresses for use. Leaving default VLAN1 alone (mgmt), I created VLAN10 (192.168.0.0/24) and VLAN20 (172.16.3.0/24) on the CBS350.ISP router "internal" ip 172.16.2.1/24On CBS350 port G...
CML 2.7 NODE not working
I recently downloaded CML 2.7 but the NODES arent working. Memory is at 4017200 % on one node. Can someone help resolve this issue?
Resolved! RRM Power on 6GHz not match between IOS version 17.9.4a and 17.12.3
I've migrated one pair of 9800-80 from 17.9.4a to 17.12.3. I noticed that the APs w/ RRM on the new 17.12.3 on 6GHz have drop drastically up to 8 dBm (see attched picture). Is anyone aware of this change and why on 17.12.3?
WLC 5508 licenses
I have a WLC with 11 registered access points I tried to integrate a new equipment, but I see that I already have my 37 licenses in use. Can you guide me and let me know what this is due to?there is a way to release licenses from the WEB portal or...
IP routing using domain
The host for my current server (Windows Hyper-V machine with four or five VMs) that handles my email and web sites is going away. I'm planning on moving that physical server to my house and using DDNS to route that traffic in. Realize this is very lo...
Cisco advsecurity and SecurityK9 license transfer.
Hi all, I have a bit of an issue where I work in that we have a number of very old series 800 routers with either an advsecurity license or a securityk9 license installed, I don't have the smart accounts for any of these (before my time) and I am now...
MACSec not supported on N7K-F312FQ-25?
Hi All,Can any one confirm that on a N7K-F312FQ-25 SUB2E is IEEE 802.1AE MACsec not supported?thanks with any pointers.with kind regardspiotr
Can you pls suggest ethernet switch which should support 1G, 2.5G, PTP
Could you pls suggest cisco ethernet switch which should support 1G, 2.5G in RJ45 mode along with TSN, PTP protocol, IEEE 1588
Nexus 9332C Booting ACI image from boot loader issue
Hi Guys, I am looking for some help as I hit obstacles and I think that I have tried all possible options, to get this issue resolved.So I was converting Nexus 9332C from NX-OS mode to ACI mode to version aci-n9000-dk9.14.2.6o.bin and at some point p...
Resolved! ISE Failures - MAB instead of 802.1x
Hello, I've been struggling with an issue in our ISE deployment for months. Basically, we are trying to restrict wired network access for computers by looking for 802.1x and then authorizing if the CA issuer for the machine cert is our internal CA....
Stop in progress template provisioning
Hello everyone. I'm very new to DNAC or Catalyst Center. I've setup a project with a template to add a simple configuration to switches. It currently has been in progress for 10 days and hasn't made a change to a switch yet. I'd like to cancel th...
PBR on ASA to Interface Without Directly Connected Next Hop
I have an ASA on which I'm trying to use PBR to route to one of two ISPs which I'll call "slow" and "fast." The interface to the slow ISP is connected to a subnet on which the next-hop address is clearly in the subnet and it would count as "directly ...
Interface Vlan administrativamente inativa
Acabei de criar uma vlan, atribuí-la a uma porta em nosso 6509, atribuí à vlan um endereço IP e quando eu disparo o comando, show int vlan 31 ele diz que a vlan está administrativamente inativa. Não consigo descobrir o que está acontecendo aqui? emit...
