Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1935960members
1260459discussions

Community Activity

Force dual-5ghz radios on 3802I ME cluster

Hi everyone,1. How can I force dual-5ghz radios on a cluster of 3802I in Mobility Express? I know it is possible to set the XOR radio to be 5GHz for each AP. Is there a more efficient way to set for the entire AP group?2. Is it possible to disable th...

Resolved! upgrade process of firepower 2130

hello We have a old fire power that I have no idea how to upgrade. The actual device is a Cisco Firepower 2130 Threat Defense (77) Version 7.0.4 . Cisco Adaptive Security Appliance Software Version 9.16(3)18. and we have a FMC that is Cisco Firepower...

SXP between C9300 and C2960X

Hello everyone,We would like to use our “old” C2960X devices, which we have in large numbers, to connect simple devices such as printers or PCs that do not require PoE. The goal is to use SGT for these devices. I have already read that it is not poss...

p11l by Level 1
  • 385 Views
  • 19 replies
  • 0 Helpful votes

Cisco 9300 switch doesn't connect via SSH

I have a couple of switches that are trunked via a LAN cable from another switch. I noticed that these switches sometimes have a hard time to SSH into. I get the error: "Connection timed out". After a while and a few tries I can connect just fine. I ...

Rick001 by Level 1
  • 608 Views
  • 20 replies
  • 0 Helpful votes

Cisco 730 Headset problems

I just bought a Cisco 730 Headset. I've installed the latest firmware (which took a log time to install comparing to other brands) this are the list of problems that I've noticed so far.Clamping force in the ears is too strong to the point of becomin...

LuisPerez by Level 1
  • 2826 Views
  • 8 replies
  • 0 Helpful votes

can not boot into 3.2 ISO image from the VM-based

trying to  migrate our ISE nodes to 3.2 version in a VM-based infrastructure, I am trying to boot VMs into the ise-3.2.0.542a.SPA.x86_64.iso image as obtained from Cisco's software download center but I keep getting the attached error. It is worth no...

Amen_0-1715239112948.png
Amen by Level 1
  • 93 Views
  • 2 replies
  • 0 Helpful votes

aaa server radius dynamic-author

SW2(config)#aaa server radius dynamic-authorSW2(config-locsvr-da-radius)#client 192.168.100.210 server-key Test123SW2(config-locsvr-da-radius)#client 192.168.100.220 server-key Test123Those commands means that we set AAA server (ISE1 and ISE2 in this...

Jason2005 by Level 1
  • 58 Views
  • 2 replies
  • 0 Helpful votes

Web Auth 9800 Redirection Issue

We have recently migrated to Cisco Catalyst 9800 and we having an issue with a captive portal/web authentication. in the old 5508 we point to the same portal with no issues. However, the portal doesn't work on the new WLC. We have a publicly signed c...

Tinei by Level 1
  • 1563 Views
  • 9 replies
  • 0 Helpful votes

Enter rommon NCS540 XR

Hello,I need to enter in rommon to change the confreg because I cannot use "conf t" in the actual configuration.I tried during booting to press "Break" from Putty terminal but is not able to run into rommon.My intention was to check the following lin...

kriskrs by Level 1
  • 68 Views
  • 1 replies
  • 0 Helpful votes

IOS IPv6 CoPP

I'm trying to configure IPv6 access for a BGP session and I want to control this through CoPP, to have more control plane security on my Cisco router with IOS, I did an initial configuration and it continues to accept connections from IPs that I didn...