Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Profiling Wired Endpoints without 802.1x or MAB using IBNS2.0
by Matt Albrecht -
Profiling Wired Endpoints without 802.1x or MAB using IBNS2.0
by Matt Albrecht -
Two Mac addresses from the FTD 2110 MGMT interface
by willpkk01 -
L3 Switches connecting to Firewalls
by Ranjita -
Setting UP a SECOND ASA5506-x firewall
by Myleslandish -
Site-to-Site IPSec with VTI - Initial delay up to 60 seconds
by Plamen Mladenov -
Empowering Sustainability with Cisco and adidas
by Sabah Kadir -
Puzzling results when pasting in ACL config to switch
by pietro manicioto
Community Activity
Two Mac addresses from the FTD 2110 MGMT interface
Hello, I deployed a new FTD 2110 on our company network and I'm seeing two different mac addresses on the switch port that the MGMT interface is connected to. I know that the one mac address is associated with the actual MGMT interface, but can anyon...
ASA5516 Recommended software version
I am configuring ASA5516 from scratch and trying to find out the current recommended versions.Could you please advise?Curretly:ASA Software Version: 9.8(2)Firepower Extensible Operating System Version: 2.2(2.52)Device Manager Version: 7.9(2)152
Wired Guest issues in foreign-acnhor setup
Wired guests are not able to get out to internet, they can ping only at when payload is set to 1300 bytes or lower, this seems like an MTU issue, but its only effecting wired guest not wireless guest. Setup is a 9800 foreign on 17.9.5 code and 5520 a...
C9800-80 in HA cannot install APSP6
Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question: Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...
Client roaming between APs at high traffic load cause 3 second gap
We are operating our vehicles remotely in the underground mines over Wi-Fi, the data load from the machine is constant around 30Mbit/s (yes, six to eight HD-cameras).When switching between APs we have noticed that we sometimes get a transmission gap ...
Loading config from file doesn't import MAC address table.
I'm using a 9200 device running IOS 17.9.I use a script and spreadsheet to generate my config file, which I then copy onto my devices via TFTP and then copy to the running config. Nothing unusual there. However, if I then ask the device to show me th...
Resolved! UCCX Call redirect to voicemail issue
Hi, We have some scripts that send a call redirect to a user's voicemail greeting and this works fine, using the call redirect step (destination = VM pilot, Called address reset to user's Ext.).The current set up from CUCM to Unity is SCCP, and I've ...
Rebuild Cisco ACI with a new version
Hi, we have a Cisco ACI in our LAB enviroment with an older version 2.2. We'd like reset/clean all the fabric (n.3 APIC,n.2 Leaf and n.2 Spine) and restart with a new version, the 5.2. Our hardware support it We don't need the backup of actual config...
Reinstall Prime VM
We have a Cisco Prime 3.10 VM running in a VMware ESX. We have to move it to a new environment with VMware ESX. What is the best way to proceed?
redundancy in core layer
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
Configure Localized ISE Installation
The Cisco Document Team has posted an article. This document describes how to configure the Localized Identity Services Engine (ISE) Installation to reinstall or upgrade ISE. Know of something that needs documenting? Share a ne...
Troubleshoot VRRPv3 Related Issues with IPv6
The Cisco Document Team has posted an article. This document describes the steps to troubleshoot Virtual Router Redundancy Protocol Version 3 (VRRPv3) with IPv6 in Nexus 9000. Know of something that needs documenting? Share a n...
Configure Route Leaking for Service Chaining in SD-WAN
The Cisco Document Team has posted an article. This document describes how to configure and verify Service Chaining to inspect traffic across different VRF. Know of something that needs documenting? Share a new document request...
Cisco Codec Plus Not going to standby
Hi AllWe have a codec plus that refuses to go into standby . It will go into half sleep mode but as soon as that period has ended the system immediatly wakes back up. The unit does not have a control system connected and it does not have a content...
Upgrading 1 access point in ME from 8.5 to 8.10.
I am trying to upgrade my 2801i in mobility express from 8.5 to 8.10. Note:- My main wlc is already in 8.10, I need to upgrade another access point so that it can join main ME WLC.
